Cushman MINUTE MISER 628808 Owner's Manual page 60

APPENDIX A
Read all of this manual to become thoroughly familiar with this vehicle. Pay particular attention to all Notices, Cautions, Warnings, and Dangers.
SAVE THESE IMPORTANT
SAFETY INSTRUCTIONS
This manual contains important safety, operating, and
installation instructions – read before using charger.
Battery Safety Information
Warning:
Use charger only on battery systems with an
algorithm selected that is appropriate to the specific battery type.
Other usage may cause personal injury and damage. Lead acid
batteries may generate explosive hydrogen gas during normal
operation. Keep sparks, flames, and smoking materials away from
batteries. Provide adequate ventilation during charging. Never
charge a frozen battery. Study all battery manufacturers' specific
precautions such as recommended rates of charge and removing
or not removing cell caps while charging.
Electrical Safety Information
Danger:
Risk of electric shock. Connect charger power cord to
an outlet that has been properly installed and grounded in
accordance with all local codes and ordinances. A grounded outlet
is required to reduce risk of electric shock – do not use ground
adapters or modify plug. Do not touch uninsulated portion of
output connector or uninsulated battery terminal. Disconnect the
AC supply before making or breaking the connections to the
battery while charging. Do not open or disassemble charger. Do not
operate charger if the AC supply cord is damaged or if the charger
has received a sharp blow, been dropped, or otherwise damaged in
any way – refer all repair work to qualified personnel. Not for use by
children.
Operating Instructions
CAUTION: Charger enclosure may be hot during charging. Use hand protection if handling the charger while charging.
1. Extension cords must be 3-wire cord no longer than 30m(100’) at 10AWG or 7.5m(25’) at 16AWG per UL guidelines.
2. Only connect ONE QuiQ charger to a single 15A circuit or the circuit may become overloaded.
3. Charger 10-LED Display
Maintenance Instructions
1. Do not expose charger to oil, dirt, mud or direct heavy water spray when cleaning vehicle.
2. The enclosure of the charger has been tested successfully to EN60529, meeting IP66. The AC supply inlet is rated
to IP20, which is suitable for indoor use only. Keep all AC connections clean and dry.
A - 2
User's Guide for:
912-2400, 912-3600-07, 912-4800-14
LED indications following “Power-On Self Test” flashes:
Ammeter Solid:
(Amber)
Flashing:
80% Charge Solid:
(Amber)
Flashing:
100% Charge Solid:
(Green) Flashing:
AC On Solid:
(Amber) Flashing:
Fault Flashing:
(Red)
INFORMATIONS IMPORTANTES
DE SÉCURITÉ
Conserver ces instructions. Ce manuel contient des instructions
importantes concernant la sécurité et le fonctionnement.
Information de Sécurité de la Batterie
Attention:
Utiliser seulement sur les systèmes batteries avec
un algorithme approprié au type spécifique de batterie. D´autres
types de batteries pourraient éclater et causer des blessures ou
dommages. Les batteries peuvent produire des gaz explosives en
service normal. Ne jamais fumer près de la batterie et éviter toute
étincelle ou flame nue à proximité de ces derniers. Fournisser la
bonne ventilation lors du chargement. Ne jamais charger une
batterie gelée. Prendre connaissance des mesures de précaution
spécifiées par le fabricant de la batterie, p. ex., vérifier s´il faut
enlever les bouchons des cellules lors du chargement de la
batterie, et les taux de chargement recommandés.
Information de Sécurité Électrique
Danger:
Risque de chocs électriques. Ne pas toucher les
parties non isolées du connecteur de sortie ou les bornes non
isolées de la batterie. Toujours connecter le chargeur à une prise
de courant mise à la terre. Ne pas ouvrir ni desassembler le
chargeur – referer toute reparations aux personnes qualifiés. Pas à
l´usage des enfants.
Displays approximate scale of current output during
charging.
High internal temperature, current output reduced.
Also displays algorithm #1-6 for 11 seconds if no
battery is connected.
Bulk charge phase complete, 80% charged. In
Absorption phase.
With no battery connected, indicates algorithm #
selected by number of flashes.
Charging complete. Charger in Maintenance Mode.
Absorption phase complete. In Finish phase
AC Power good
Low AC Voltage, check voltage and extension cord
length (see above for guidelines).
Charger error. Reset charger power and refer to
Troubleshooting below.