Related Manuals for Kramer RC-43T
Summary of Contents for Kramer RC-43T
-
Page 1: User Manual
K R A ME R E LE CT R O N IC S L TD . USER MANUAL MODEL: RC-43T Remote Controller P/N: 2900-300301 Rev 2... -
Page 3: Table Of Contents
Figure 2: RC-43T Remote Controller Rear View Figure 3: RC-43T Remote Controller Exploded Rear View Figure 4: Connecting the RC-43T Remote Controller Figure 5: RC-43T K-Net Wiring Figure 6: RC-43T K-Net Bus Termination Switch Figure 7: Mounting the RC-43T in a Wall Box RC-43T – Contents... -
Page 4: Introduction
Room Connectivity; GROUP 10: Accessories and Rack Adapters; GROUP 11: Sierra Video Products; GROUP 12: Digital Signage; and GROUP 13: Audio. Congratulations on purchasing your Kramer RC-43T which lets you control an A/V system with ease in applications such as, multimedia classrooms or conference rooms. -
Page 5: Getting Started
Avoid interference from neighboring electrical appliances that may adversely influence signal quality Position your Kramer RC-43T away from moisture, excessive sunlight and dust This equipment is to be used only inside a building. It may only be connected to other equipment that is installed inside a building... -
Page 6: Safety Instructions
Kramer Electronics has made arrangements with the European Advanced Recycling Network (EARN) and will cover any costs of treatment, recycling and recovery of waste Kramer Electronics branded equipment on arrival at the EARN facility. For details of Kramer’s recycling arrangements in your particular country go to our recycling pages at http://www.kramerelectronics.com/support/recycling/. -
Page 7: Overview
Overview The RC-43T is a remote control keypad with six touch-sensitive, backlit buttons. It is designed to be used in conjunction with room controllers, such as the SL-1. Using the Kramer K-Config software, each button on the RC-43T can be programmed on the room controller with a function, where each function can comprise multiple individual actions. -
Page 8: Defining The Rc-43T Remote Controller
Defining the RC-43T Remote Controller Figure 1 shows the six, touch-sensitive, backlit buttons on the front panel of the RC-43T. Figure 1: RC-43T Remote Controller Front Panel Feature Description Six Touch-sensitive Program the button functions on the connected room Buttons... -
Page 9: Figure 2: Rc-43T Remote Controller Rear View
Figure 2: RC-43T Remote Controller Rear View Feature Description Mounting Holes Attach the RC-43T to the wall mounting box with the screws provided (see Section 6.2) Front Panel Cosmetic panel that covers the PC Board and houses the removable buttons... -
Page 10: Figure 3: Rc-43T Remote Controller Exploded Rear View
Figure 3 shows an exploded rear view using the same identification table as Figure Figure 3: RC-43T Remote Controller Exploded Rear View RC-43T - Defining the RC-43T Remote Controller... -
Page 11: Connecting The Rc-43T
Figure 4: Connecting the RC-43T Remote Controller To connect the RC-43T as illustrated in the example in Figure Connect the RC-43T to a room controller, (for example, the SL-1) via the K-NET 4-pin, (see Section 5.1) terminal block on the rear panel of the... -
Page 12: K-Net Wiring
K-NET Wiring The K-NET connector on the RC-43T must be connected to a room controller via a four wire cable as shown in Figure Figure 5: RC-43T K-Net Wiring Note: The RC-43T is always device ID 2 on the K-NET bus and cannot be changed. -
Page 13: Installing The Configuration Software
Figure 6: RC-43T K-Net Bus Termination Switch To terminate the K-NET bus on the RC-43T: Slide SW7 (see SW7) into the position shown in Figure 6 Installing the Configuration Software Download the K-Config configuration software from our Web site and install it (refer to the K-Config User Manual). -
Page 14: Installing The Rc-43T
Section 6.2) Installing the Front Panel Buttons The RC-43T is supplied with preprinted buttons from which you can choose the six that best represent the functions you wish to assign the buttons. To install the front panel buttons: 1. Remove the front panel (see... -
Page 15: Installing The Rc-43T In The Wall Mounting Box
To install the RC-43T in the wall mounting box: 1. Remove the front panel of the RC-43T. 2. Insert the RC-43T into the wall mounting box and secure it using the two M3 x 10mm screws supplied. 3. Replace the front panel of the RC-43T. -
Page 16: Technical Specifications
6.9cm x 1.6cm x 11.4cm (2.72" x 0.63" x 4.5") W, D, H WEIGHT: 0.3kg (0.66lbs) approx. Four 6/32x1/2” screws INCLUDED ACCESSORIES: One white faceplate One black faceplate OPTIONS: K-NET cable Specifications are subject to change without notice at http://www.kramerelectronics.com RC-43T - Technical Specifications... - Page 18 For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to this user manual may be found. We welcome your questions, comments, and feedback. Web site: www.kramerelectronics.com E-mail: info@kramerel.com SAFETY WARNING...
Need help?
Do you have a question about the RC-43T and is the answer not in the manual?
Questions and answers