Advertisement
S S t t a a g g e e 6 6 : : B B u u i i l l d d i i n n g g t t h h e e C C o o c c k k p p i i t t
S S t t a a g g e e 6 6 : : B B u u i i l l d d i i n n g g t t h h e e C C o o c c k k p p i i t t
a a n n d d C C o o n n t t r r o o l l s s
PARTS LIST FOR STAGE 6:
Ni28-068
Cabane struts
Ni28-081
Control stick
Ni28-082
Trunion
WP161-12
Control stick pivot
Ni28-084
Control stick supports
Ni28-086
False nuts
Ni28-087
Aileron push levers
Ni28-088
Aileron lever "S" arms
Ni28-089
Rudder bar
Ni28-090
Rudder bar support
Ni28-091
Rudder cable yoke
Ni28-092
Rudder control pin
Ni28-093
Instrument panel
WP40264
Instrument panel support bar
WP——-
Instrument faces
Ni28-094
Fuel handle
Ni28-095
Fuel level
WP1860
Rudder stirrups
C023
Choke
Ni28-101
Oil tank (2 parts)
A017
Aileron control false bolts
WP1205
Control cables A, B, C
C062
Lubricator
Ni28-099
Engine control quadrant
C054
Starter magneto
C055
Starter magneto handle
C058
Magneto switch
WP40224SEC Cockpit plumbing
GR9-15
Crankshaft
GR9-16
Motor mounting ring
GR9-17
Pump & magneto gears
GR9-18
Oil pump
GR9-19
Magneto
GR9-20
Front crankshaft flange
GR9-21
Rear crankshaft flange
GR9-22
Air manifold & fuel pipe
WP3680-24
Diagonal braces
Ni28-069
Stiffening plates R-L pair
Ni28-070
Stiffening plates
Ni28-071
Cable brace plates
Ni28-098
Seat back
WP0978
Fuel tank straps
Ni28-100
Seat
Ni28-105
Fuel filler pipe/caps
Ni28-076
Arc strut brace
Ni28-102a,b,c,d Main fuel tank
Ni28-103
Saddle fuel tank
A037
Wire connections
MODELER PROVIDES Fuel tank skin
Ni28-???
Fuel tank strap buckles
W042
Turnbuckles
WP1205
Rigging cable
a a n n d d C C o o n n t t r r o o l l s s
2 R-L pair Britannia castings
1 Britannia casting
1 Britannia casting
1 3/64 x 1/2 Brass rod
2 Britannia castings
6 Britannia castings
2 Britannia castings
2 Britannia castings
1 Britannia casting
1 Britannia casting
1 Britannia casting
1 2mm aluminum rivet
1 Britannia casting
1 5/64 Brass rod
1 Gloss paper - set of three
1 Britannia casting
1 Britannia casting
2 1/4" aluminum tape
1 Britannia casting
2 Britannia castings
2 Britannia castings
6 Metal-gray thread
1 Britannia casting
1 Britannia casting
1 Britannia casting
1 Britannia casting
1 Britannia casting
2' 031" Brass wire
1 4x66mm Steel rod
1 Britannia casting
2 Britannia castings
1 Britannia casting
1 Britannia casting
1 Britannia casting
1 Britannia casting
1 Britannia casting
2 3/64 x 3/64 wood strips
2 Britannia casting
2 Britannia casting
4 Britannia casting
1 Britannia casting
4 1/4" Copper tape
1 Britannia casting
2 Britannia castings
1 Britannia casting
1 Britannia casting (4 parts)
1 Britannia casting
1/4" lengths of copper spring
1 Sheet aluminum ñ SODA CAN
4 Britannia castings
12 Britannia metal
4' Metal-gray thread
the trunion(Ni28-082) through the rectan-
gular opening in the control stick(Ni28-
081) and pin it in place with pivot
(WP161-12). You will need to drill out the
holes in the stick for the pivot pin and
must cut the pin to length. Glue itís ends
to the molded-on false nuts, making sure
that the stick moves easily back and forth
on the trunion.
the control stick, push lever, and "S" arms
are designed to move in two axes. This is
accomplished in the model by the simple
expedient of allowing sufficient free play
in the linkage. It is suggested that you test
fit the linkage before gluing on the false
nuts, and then ream the holes in the push
levers(Ni28-087) if needed.
and aileron "S" arms(Ni28-088) by means
of the aileron control false bolts(A017)
and false nuts (Ni28-086). Attach these
assemblies to the trunion pivots and
secure with false nuts. Make sure that all
the joints move freely.
084)
braces(WPO3631-24) that run across the
cockpit. The braces fit within the slots,
which face each other, on the supports.
Next insert the trunion pins into the brack-
ets on the supports and gently crimp the
brackets to secure the trunion pins but still
allowing the control stick to pivot freely
side to side.
tor control cables(WP1205) ("A" and "B"
in Figure 6/2) to the control stick. Run the
cables back through the fuselage, through
the left outer of the bottom four lightening
holes of formers #4-6, then through the
left outer of the four holes in the brace
across former #7. Temporarily tie them
off at former #10.
parts Ni28-089-092 and WP1860 as
shown in Figure 6/3. Make sure the rudder
bar(Ni28-089) swings freely. Make the
stirrups
23
23
Control stick:
Referring to Figures 6/1 and 6/2, insert
In the actual aircraft, the joints between
Unite the aileron push levers(Ni28-087)
Glue the control stick supports(Ni28-
into
place
on
the
Finish this step by attaching the 2 eleva-
Rudder controls:
The rudder bar assembly consists of
from
the
1/4"
3x3mm
aluminum
Advertisement
