Speaker Connections; Analogue Audio Connections - Cambridge Audio Minx Xi User Manual

Connecting to a wireless network
IMPORTANT: Do not plug/unplug the Wi-Fi aerial dongle when the unit is on.
Place the Minx Xi in range of your wireless network (usually 10-30m of a suitable
wireless transmitter, although this is affected by walls and the construction of your
building) and turn it on, via the front panel switch.
Internet
Wireless broadband
Router/Modem
The Minx Xi will automatically connect and obtain an IP address from your wireless
network. For advanced users, if you would like to give your Minx Xi a static IP
address, then see the 'Network config' section of the manual.
Note: If you make a mistake at any point, you can always press the
back to the previous screen.
The unit will now scan for all available wireless networks and will display "Scanning".
If it can't find one then the display will say: "No Wireless Networks Found". If this
happens then you need to either move the Minx Xi nearer your wireless access point
or investigate if there is an issue with your wireless network.
When the Minx Xi finds your wireless network, it displays the broadcast name
(ESSID) for the access point – this is a name allocated to the access point by
whoever set up the network, it may either be a default name for your router/
wireless or may be a more familiar name such as "Johns Wi-Fi" etc. If your Minx Xi
finds more than one wireless network you can simply choose which one you want to
connect to. Turn the rotary dial to see the ESSID for each wireless network.
When the ESSID for the wireless network you want to connect to is displayed on
the screen, press the SELECT button. If your network is not configured with an
encryption code, the screen should say "Connecting to network" then "Network OK".
If the screen displays either "Enter WEP key" or "Enter WPA key", then the network
is using one of the supported encryption systems: Wired Equivalent Privacy (WEP)
or Wi-Fi Protected Access (WPA). You now need to enter your correct WEP or WPA
code. The person who set up the wireless network in the first place will know what
this code is (or be able to reset it to a new known code); if that person is not you,
then you need to find out what it is.
After 3 seconds, the display goes into the code entry mode. To enter the code, use
the rotary dial to select each character of the code in turn, pressing the SELECT
button after entering each character.
Note: The WEP and WPA codes are case sensitive, so you must enter them exactly.
10
After entering the final character, use the rotary dial to select the
press the SELECT button. It's a little fiddly but you will only need to do this once. The
Minx Xi will remember this code and use it automatically from now on.
The unit should now be able to connect to the network.

Speaker connections

Check the impedance of your speakers. Speakers with an impedance of between 4
and 8 Ohms are recommended.
10-30m distance
The red coloured speaker terminals are positive (+) and the black speaker
button to go
terminals are negative (-). Make sure correct polarity is maintained at each speaker
connector or the sound can become weak and "phasey" with little bass.
Prepare the speaker cords for connection by stripping off approximately 10mm
(3/8") or less of the outer insulation. More than 10mm could cause a short circuit.
Twist the wires tightly together so there are no loose ends. Push in the terminal,
insert the speaker cable through the hole in the side of the terminal and release
the terminal so it clamps down on the wire.
Note: All connections are made using standard loudspeaker cable. If an active
subwoofer is used, connect via a standard single RCA/phono cable (often referred
to as a 'Sub-Link').

Analogue audio connections

Note: Do not plug in the mains power lead or turn the unit on until all connections
have been made.
Audio player/recorder
(Tape/MD/CD-R)
CD player
Connect to source equipment using stereo phono/RCA cables (stereo 2RCA- 2RCA).
Tape/MD/CDR recorder/players require two sets of stereo phono/ RCA cables, one
for recording, one for listening.
character and
Out
Out