Advertisement
Quick Links
Advertisement
Related Manuals for Beamz LS-1W RGB DMX
Summary of Contents for Beamz LS-1W RGB DMX
- Page 1 LS-1W Animation Laser RGB DMX 152.897 Instruction Manual...
- Page 2 （Before using，please read the user manual carefully.） This is product integrates many advanced technologies like optics, electronics, digital graphic processing, especially designed for dancing halls and DISCO. According to music rhythms, built-in beam program can be activated; if using smoke, light curtain wall and time tunnel can be formed to create a colorful and fantastic laser world.
- Page 3 Animation Laser (without PC interface) Front panel and rear panel schemes (According to different models, the panel will be different.) ○ ,1 light outlet ○ ,2 Fan ○ ,3 power supply ○ ,4 Sound control sensitivity knob ○ ,5 DMX XLR ○...
- Page 4 1. Operating Instructions DIPSWITCH CHART FUNCTION SOUND ACTIVE AUTO MODE Animatiom Sound control Auto working Animation 1.1 Single user mode: 1.1.1 Use dip switch to set operating mode(See the table below）. Set the operating mode according to clients’ requirement: SOUND ACTIVE or AUTO MODE.
- Page 5 1.2 Scanner master & slave synchronous mode: The switching method of Master & slave synchronous mode Master: sound activation( switch 0 in address code) or auto mode( switch 1in address code) or animation mode( switch 1,2 in address code) Master ( sound activation, auto, animation mode)
- Page 6 Slave: switch 2 or switch 3 1.1 Set working mode. Set a laser in Master& Slave mode(MASTER： SOUND/AUTO）, and other lasers are all set in Slave mode. 1.2 Connect the line. Use XLR-XLR line to connect the XLR output of the master to the XLR input of the first slave, and then connect the XLR output of the first slave to the XLR input of the second slave.
- Page 7 DMX mode switching method: When in DMX mode, the DMX controller controls the laser, and the corresponding function of every channel is shown in attachment. The DMX address code is in the attached address table. First to ninth: starting address The tenth: sound control/ DMX functions change OFF：sound control ON：...
- Page 8 ○ ○ ,5 Sound control sensitivity knob ,6 DMX XLR ○ ○ ,8 Address code switch ,7 power socket ○ ,9 sound control MIC 2.The operating method of lasers with PC interface is the same as that of lasers without PC interface. So I will not repeat here. And now let’s introduce how to use PC interface.
- Page 9 on. Please refer to the user manual of lasers with SD card and CD. DMX512 Controller connecting lasers: N………. DMX Console(Sending end) laser1(Receiving end） Laser 2 Laser 3 ……………….. For example, If the laser has 11 channels, the address is set as: 000000001 000001100 000010111 …………...
- Page 10 the terminal should connect with 120 Resistor to avoid signal disturbing. 2. Address allocation: DMX 512 supports 512 channels. If every laser has 16 channels, so is can connect 32 pieces of lasers. Usually, RGB LED has 3 channels, so DMX 512 console can connect 170 pieces of LED in every line.
- Page 11 Common abnormal phenomena & failure elimination In the sound activation mode, beam effects don’t change with music. Elimination method: Rotate right (Sensitivity control) knob until you obtain satisfactory effects. When in DMX512 mode, push-and-pull controlling rob doesn’t work. Elimination method: First check whether DMX 512 controller can work normally and whether the signal lines are connected correctly;...
- Page 12 Form 1 Channel Function Value Description Close, laser OFF 0～49 Static patterns of DMX mode 50～99 Mode 100～149 Dynamic patterns of DMX mode Sound active mode 150～199 200～255 AUTO mode Pattern selection 52 static/dynamic patterns 0～255 Position-X Adjust position-X 0～255 Position-Y Adjust position-Y 0～255...
- Page 13 Form 2 DMX512 value Control function sound control （3-10 channels don’t work） 0~51 Auto mode（3-10 channels don’t work） 52~103 1control mode 104~155 Animation mode Manual mode，sound control start 156~206 207-255 Auto mode, auto start 0~15 Light free 16~25 No blanking 26~135 Water-flow effect, closer to 135, water flow blanking...
- Page 14 Form 3 DMX Address form...