Mitsubishi QJ71C24/-R2 User Manual page 70

3 SPECIFICATIONS
Address
Decimal (Hex)
Application
CH1 CH2
144 304
(90 ) (130 )
H H
For designation of
mode switching
145 305
(91 ) (131 )
H H
146 306 Signal setting
(92 ) (132 ) ( 1)
H H
147 307
(93 ) (133 )
H H
For designation of
transmission
148 308
control
(94 ) (134 )
H H
149 309
(95 ) (135 )
H H
150 310
(96 ) (136 )
H H
For designation
of communica-
tion control
151 311
(97 ) (137 )
H H
3 - 20
Name
Switching mode no. designation (0001
0001 : MC protocol (format 1)
H
0002 : MC protocol (format 2)
H
0003 : MC protocol (format 3)
H
0004 : MC protocol (format 4)
H
Transmission specifications after switching designation
Designates transmission specifications (below) after switching
when b15 of this area is 1 (ON).
Operation setting (b0)
Data bit (b1)
Parity bit (b2)
Odd/even parity (b3)
Stop bit (b4)
Sum check code (b5)
Write during RUN (b6)
Setting modification (b7)
Communication rate (b8 to b11)
For system (b12 to b14)
Transmission specifications after switching (b15) designation
RS and DTR signal status designation
0: Off 1: On
RS signal (b0)
DTR signal (b2)
For system (b1), (b3) to (b15)
DTR/DSR(ER/DR), DC control designation
• Transmission control (b0)
0: DTR/DSR control 1: DC code control
• DC1/DC3 control (b8)
0: No control 1: Controlled
• DC2/DC4 control (b9)
0: No control 1: Controlled
DC1/DC3(Xon/Xoff) code designation
• DC1 code (b0 to b7)
00 to FF : DC1 code
H H
• DC3 code (b8 to b15)
00 to FF : DC3 code
H H
DC2/DC4 code designation
• DC2 code (b0 to b7)
00 to FF : DC2 code
H H
• DC4 code (b8 to b15)
00 to FF : DC4 code
H H
Word/byte units designation
0: Word units
CD terminal check designation (for RS-232)
0: Check
to 0007 , 00FF )
H H H
0005 : MC protocol (format 5)
H
0006 : Non procedure protocol
H
0007 : Bidirectional protocol
H
00FF : GX Developer
H
connection
0: Independent 1: Link
0: 7 bit 1: 8 bit
0: No 1: Yes
0: Odd 1: Even
0: 1 bit 1: 2 bit
0: No 1: Yes
0: Prohibited 1: Allowed
0: Prohibited 1: Allowed
50 bps to 230400 bps
All 0
0: Match settings in GX Developer
1: Match settings in this area
1: Byte units
1: No check
MELSEC-Q
Applicable
Registration
Initial
protocol
allowed/not
value
allowed
MC Non Bi
0 RW Not allowed
RW
0005 Allowed
H
0
RW
1311
H
Allowed
1412
H
0
RW
1
Reference
section
Section
4.5.2
Chapter 15
of User's
Manual
(Application)
Section 3.2.1
Section
8.4.5
Chapter 7
of User's
Manual
(Application)
Chapters 6
Chapter 7
Section
8.4.5
Section
3.2.1
Section
8.4.5
3 - 20