Connecting A Dvd Player Or Other S-Video Device - Mitsubishi WS-65315A Owner's Manual

Connecting a DVD Player or Other S-Video Device

Note: The TV back panel and connections shown here are for reference only and may vary by model.
�
�
�
� � � � � �
�
�
�
� �
�
�
� � � � � � � �
Figure 9. Connecting a DVD Player with Component
Video.
See Appendix, page 65, for component
video signal compatibility information.
For digital audio connections, see your
DVD and A/V receiver Owner's Guides.
��������������
����������������
� � � � �
�
�����
�
���
������������������
�����
���
�
Figure 10. Connecting an S-Video Device.
18
���������
� �� � � � ���� �����
� �
�
�
�
��
�
� �
�����
����� �
� � � � �
�
����� �
� �� ��
���
��� ���� �����
� � � � � � � �
� � � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � � �
� � � � � � �
� � � � � � � � � � �
�����
� � � � � � � � � � � � � � � � � � � �
�
� � � � � � � � � � � � � � � � � � �
� � � � � � � � �
�
� � � � � � � � � � � �
� � � � � � � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � ���
� � � � � � � � � � � �
� � � � � � � � � � � � � � � �
� � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �
� � � � � � � � � � � � � �
� � � � � � � � � � �
�
�
�������
� � � � �
������
���� �
������
����� �
� � �� �
��������� �������� ���������
� � �����
�
�
�
�
DVD Player with Component Video
(Figure 9)
1. Connect the Component Video cables from
(YCb Cr or Y Pb Pr) VIDEO OUT on the back of
the DVD player to COMPONENT (1 or 2) on the
TV back panel. The correct connections are:
A. Y to Y
B. Cb or Pb to Pb
� � � �
C. Cr or Pr to Pr
2. Connect a set of audio cables from AUDIO OUT
on the back of the DVD player to COMPONENT
AUDIO Input (1 or 2) on the TV back panel.
• The red cable connects to the R (right)channel
• The white cable connects to the L (left) channel
Note: Some video game systems support DTV
resolutions via component connections.
Please refer to your video game console
Owner's Guide for setup information.
Note: For optimal DVD playback performance,
Mitsubishi recommends using a progressive
scan DVD player, set to play in progressive
scan mode. You will also want to set your
player to display 16:9 widescreen. Please
refer to your DVD player's Owner's Guide.
Other S-Video Device
(Figure 10)
1. Connect an S-Video cable from VIDEO OUT
on the device back panel to VIDEO INPUT-1 or
INPUT-2 on the TV back panel.
2. Connect a set of audio cables from AUDIO OUT
on the device back panel to AUDIO INPUT-1 or
INPUT-2 on the TV back panel, matching the
input used in step 1.
• The red cable connects to the R (right) channel
�
• The white cable connects to the L (left) channel
If your S-Video Device is mono (non-stereo),
connect only the white (left) cable.