Vcr To An Antenna Or Wall Outlet Cable; Vcr To A Cable Box (Audio & Video) - Mitsubishi Electric LT-40148 Owner's Manual

VCR to an Antenna or
Wall Outlet Cable
Required: Two-way RF splitter, two coaxial cables, right
and left analog audio cables, either S-video or compos-
ite video cable.
1.
Connect the incoming cable or antenna to
RF splitter.
2.
Connect one coaxial cable from
splitter to ANTENNA IN on the VCR back panel.
3.
Connect one coaxial cable from
splitter to ANT 1 on the TV main panel.
4.
Connect either an S-Video or composite video
cable from VIDEO OUT on the VCR back panel to a
VIDEO composite or S-VIDEO jack on the TV main
panel. Connect only one type of video cable;
S-Video is recommended, if available.
5.
To use the TV speakers with the VCR, connect left
(white) and right (red) audio cables from AUDIO OUT
on the VCR to the associated AUDIO L and R jacks
on the TV main panel. If your VCR is mono (non-
stereo), connect only the white (left) cable.
VCR
S-VIDEO
OUT
4.
HDMI
4
3
2
S-VIDEO
1
4.
IR-
NetCommand
S-VIDEO S-VIDEO
Output / External
Controller Input
INPUT3
Pr
VIDEO VIDEO
L L Pb
VIDEO
AUDIO AUDIO
R R L
Y Y / VIDEO
DVI/PC
AUDIO
L L
AUDIO
AUDIO
R
R
R
INPUT2 INPUT1
DIGITAL
AUDIO
OUTPUT
L R
AVR AUDIO
OUTPUT
ANT1/MAIN
ANT2/AUX ANT1/MAIN ANT1/MAIN
TV main panel
Figure 8. Connecting a VCR to allow recording from an
antenna source.
IN on the
OUT on the RF
OUT on the RF
VIDEO
AUDIO OUT ANTENNA
OUT
IN
L R
5.
3.
5.
1.
3.
Incoming
cable
3. TV Connections
VCR to a Cable Box (Audio & Video)
Required: Two-way RF splitter, three coaxial cables,
right and left audio cables, S-Video or composite video
cable, plus video and audio cables required to connect
the TV to the cable box.
1.
Connect the incoming cable to
2.
Connect one coaxial cable from
splitter to CABLE IN on the cable box.
3.
Connect one coaxial cable from
splitter to ANT 1 on the TV main panel.
4.
Connect one coaxial cable from
box to ANTENNA IN on the VCR back panel.
VCR
HDMI
4
3
2
1
IR-
NetCommand
S-VIDEO S-VIDEO
Output / External
Controller Input
INPUT3
2. Pr
VIDEO VIDEO
Pb
L L
VIDEO
AUDIO AUDIO
R R L
Y Y / VIDEO
DVI/PC
AUDIO
L L
AUDIO
AUDIO R
R
R
INPUT2 INPUT1
DIGITAL
AUDIO
OUTPUT
L R
AVR AUDIO
OUTPUT
ANT2/AUX ANT1/MAIN ANT1/MAIN
2.
Figure 9. Connecting a VCR to a cable box
5.
Connect the cable box outputs to the TV as shown
in one of the options listed below. This connection
allows the TV to receive the best available signal
directly from the cable box.
• Figure 1, page 22: Component video output to
the TV's Y Pb Pr jacks; analog stereo audio to
the associated AUDIO jacks.
• Figure 2, page 22: HDMI output to the TV's
HDMI jack.
• Figure 4, page 23: S-Video output to the TV's
INPUT 3 S-VIDEO jack; analog stereo audio to
the INPUT 3 AUDIO jacks.
IN on the RF splitter.
OUT on the RF
OUT on the RF
OUT on the cable
S-VIDEO VIDEO
AUDIO OUT
OUT OUT
L
6.
TV
main
panel
S-VIDEO
6.
Audio and
video from
cable box
7.
3.
ANT1/MAIN
Incoming
cable
25
ANTENNA
IN
R
4.
7.
4.
Cable
box
5. OUT
IN
2.
to TV
2.
3.
1.