Using The Internal Time Code Generator - Sony DSR-1500A Operating Instructions Manual

To display the desired time data in the time
counter display
INPUT
dB OVER dB OVER
0 0 VIDEO
V:SDTI COMPOSITE
SDTI S VIDEO
-12 -12
i.LINK
-20 -20
SDI
OUTPUT
-30 -30
VIDEO
-40 -40
SDI COMPOSITE
-60 -60
SDTI S VIDEO
CH- 1 3 CH- 2 4
Press the COUNTER SELECT button on the front panel.
Each press of this button cycles through three options:
CNT value, time code, and user bit data. The time data type
indicator for each option lights as it is selected.
Time data Time data shown in the time counter
type display
indicator
COUNTER CNT (count value of the time counter)
TC Time code (when recording, the time code is
generated by the internal time code
generator; when playing back, the time code
is read from the tape.)
U-BIT User bit data (when recording, the user bit
data is according to the most recent settings;
when playing back, the user bit data is read
from the tape.)
Note
When the REMOTE indicator in the front panel display
section is lit, the COUNTER SELECT button does not
operate while the tape is moving. In such cases, use the
external equipment connected to the REMOTE connector
on the rear panel to select the time data.
46
Setting the Time Data
Time data type indicators
CL REC INHI
U-BIT SERVO
AUDIO
CH-1 1/2 CH-2 3/4 TC COUNTER NO EDIT REPEAT
ANALOG ANALOG
Y-R,B AES/EBU AES/EBU
SG SDI SG SDI SG
AUDIO
CH 1/2 HOURS MINUTES SECONDS FRAMES
CH 3/4 PB F REC MODE VITC REMOTE
S
9P i.LINK
Y-R,B 48K 44.1K 32K 2CH 4CH EDIT MODE
COUNTER SELECT button
Time counter display
To reset the CNT value
Press the RESET (NO) button in the menu control section.
This resets the CNT value to 0:00:00:00.
Note
During playback, if the recording on the tape includes
discontinuities, the counter may operate incorrectly at the
corresponding points.
Using the Internal Time Code
Generator
You can set the initial time code value before recording the
time code generated by the internal time code generator
onto a tape. In addition, you can use the user bits to record
such data as the date, time, scene number, reel number, or
other useful information.
When an external time code generator is connected to the
TC IN connector, the internal time code generator can be
locked to (synchronized with) an external time code.
To set the initial time code value and user
bit data
dB dB INPUT
OVER OVER U-BIT
0 0 VIDEO AUDIO
V:SDTI COMPOSITE CH-1 1/2 CH-2 3/4
SDTI S VIDEO ANALOG ANALOG
-12 -12
i.LINK Y-R,B AES/EBU AES/EBU
-20 -20 SDI SG SDI SG SDI SG
OUTPUT
-30 -30
VIDEO AUDIO
-40 -40
SDI COMPOSITE CH 1/2 HOURS
-60 -60
SDTI S VIDEO CH 3/4
CH- 1 3 CH- 2 4 Y-R,B 48K 44.1K 32K
1
Press the COUNTER SELECT button to light the time
data type indicator "TC" or "U-BIT."
TC: To set the initial time code value
U-BIT: To set user bit data
The current time code value or user bit data is shown
in the time counter display.
3 2 7
CL
SERVO REC INHI
TC COUNTER NO EDIT REPEAT
MINUTES SECONDS FRAMES
PB F S REC MODE VITC REMOTE
2CH 4CH EDIT MODE 9P i.LINK
1
4,5,6