Others - Panasonic sc-all5cd Operating Instructions Manual

Others

Auto off function
As a factory default, this unit will turn to standby mode
automatically if there is no sound and it is not being
used for approximately 20 minutes.
To cancel this function
1
Press [SETUP] repeatedly to select "AUTO OFF".
2
Press [3, 4] to select "OFF" and then press [OK].
≥ To turn the function on, select "ON" in step 2.
≥ This setting cannot be selected when radio is the source.
≥ When connected to a Bluetooth
not work.
≥ When playing AllPlay/DLNA, the function does not work.
≥ If "NET STANDBY" is set to "ON", this function will also be
set to "ON". To change the setting, set "NET STANDBY" to
"OFF". (l 19)
Bluetooth
®
When "SC-ALL5CD" is selected from a paired
Bluetooth device's Bluetooth
®
on automatically from standby mode and establish a
Bluetooth connection.
®
1
Press [SETUP] repeatedly to select "BLUETOOTH
STANDBY".
2
Press [3, 4] to select "ON" and then press [OK].
≥ To turn the function off, select "OFF" in step 2.
Changing the unit and remote
control code
When other Panasonic equipment responds to the
supplied remote control, change the remote control
code.
1
Press [CD/USB] to select "CD".
2
While touching and holding [SELECTOR] on the
unit, press and hold [CD/USB] on the remote
control until the unit's display shows "REMOTE 2".
3
Press and hold [OK] and [CD/USB] on the remote
control for at least 4 seconds.
≥ To change the mode back to "REMOTE 1", press [CD/USB]
to select "CD" and then repeat the step 2 and 3 but replace
[CD/USB] with [ ].
18
RQT0A22
device, the function does
®
standby
menu, this unit will turn
®
Beep sound setting
As a factory default, there will be a beep sound when
you touch the switch on the unit.
To cancel this function
1
Press [SETUP] repeatedly to select "BUZZER".
2
Press [3, 4] to select "OFF" and then press [OK].
≥ To turn the function on, select "ON" in step 2.
≥ The function works during muting as well.
Software update
Occasionally, Panasonic may release updated
software for this system that may add or improve the
way a feature operates. These updates are available
free of charge.
You can also update the software from a pop-up
prompting you to do so on-screen within the app
"Panasonic Music Streaming" (version 2.0.8 or later)
(l 9). For details on the app, refer to the site below.
http://panasonic.jp/support/global/cs/audio/app/
(This site is in English only.)
DO NOT DISCONNECT the AC mains lead
while one of the following messages is
displayed.
"UPDATING" or "UPD
(" " stands for a number.)
≥ During the update process, no other operations can be
performed.
Preparation
≥ Turn this system on.
≥ Connect this system to the home network. (l 7)
– Make sure that the network is connected to the
Internet.
1
Press [RADIO/EXT-IN] repeatedly to select
"NETWORK".
2
Press [SETUP] repeatedly to select
"SW UPDATE" and then press [OK].
3
Press [3, 4] to select "OK? YES" and then press
[OK] to start the update.
≥ Select "OK? NO" to cancel the update.
When the update begins, "UPDATING" is
displayed. After the update has finished,
"SUCCESS" is displayed.
4
Disconnect the AC mains lead and reconnect it
after 1 minute.
≥ If there are no updates, "NO NEED" is displayed.
≥ Downloading will require several minutes. It may take longer
or may not work properly depending on the connection
environment.
%"