• Fire Box Glow • Wireless Tether Table of contents Transformer operations Running your Lionel T1 with a Lionel transformer Locking your T1 into a single operational state Using your T1 tender-mounted ElectroCoupler Your T1 RailSounds system—the basics Experiencing the range of your T1 RailSounds system...
Move ‘em out! • Get your T1 moving. Press the DIR button on your CAB-1 remote or Lionel transformer. This sequences the R2IR to the next operating state. • Adjust track voltage until your T1 moves at your desired speed.
Locking your T1 into a single operational state o select a single operational state for direction, then slow it down without stop- your Lionel T1 (example: forward only), ping. Set the Program/Run switch to PROG. you can deactivate the R2IR’s sequencing The T1 is now “locked”...
Your T1 RailSounds system—the basics ionel RailSounds is the most realistic locomotive at rest. As the T1 moves, chuffing model railroad sound system in the begins, increasing with the locomotive’s world. Your T1 features digital samples from speed. real-life steam locomotives for the ultimate To silence the steam chuffing sound (whis- in realism.
T1 telling you its R2IR the world. And remember—coming from Command reverse unit has just reset to inside your Lionel T1 tender are the authen- forward operation. tic sounds of the RailSounds digital sound • Shutdown sequence. No other model system.
Sound Activation Button for bell For AC transformers lacking a horn/whistle button The no. 610-5906-001 button works with any Lionel AC transformer except Note! no. 6-4690 Type MW. Transformers made by other manufacturers may not be compatible with RailSounds.
• Make sure track power is OFF before placing it on track. • Make sure your Lionel Command Base is ON and its communica- tions wire is connected to the COMMON post on your Lionel transformer or the U terminal on any of your installed PowerMasters.
Running your T1 in the TrainMaster Command environment our Command-equipped T1 Example Address Locomotive #1 comes factory-programmed with an ID# of “1.” To get your PowerMasters set to CMD or traditional T1 into action, set PowerMasters to CMD or set all power supplies power supplies ON FULL on full.
TrainMaster Command operations RailSounds in the Command environment our T1 RailSounds system gives you more sedate sound, as though the load even more in the TrainMaster placed on the T1 has decreased. Experience Command environment. DynaChuff on steep grades, at yard crawls, •...
Tuning your T1 performance MOMENTUM until you change it. To clear stall, press SET Simulate the labored performance of a twice, holding it for one second each time. locomotive pulling a heavy load with HIGH VOLTAGE SETTING momentum. Press L, M, or H (located under CAB-1’s removable panel) for light, medium Press ENG, the locomotive ID#, then press or heavy momentum.
TrainMaster Command operations Assigning your locomotive a new ID# s your fleet of Command- Assign a new ID# to your Example equipped Lionels grows, give Command-equipped locomotive your T1 locomotive its own ID#. Command Base ON Choose from any between 1 and 99. Place the locomotive on track Plug-in the Command Base and PowerMasters set to CMD or...
Page 13
Maintaining and servicing your Locomotive Lubricating your T1 elp your Lionel T1 lead a long and You’ll know your T1 requires lubrication productive life on your railroad by when visual inspection reveals dryness on the maintaining it properly. parts indicated in the illustration. Remove...
620-8029-300 Replacing your T1 lamps (Tender) our T1 tender is illuminated by one Service. See the Lionel Service section on page lamp, located at the rear of the tender. 16 for more information. Remove the tender body by unscrewing the Reassemble in reverse order.
CAB-1 remote will turn the smoke gen- The smoke generator requires the periodic erator on. Turning off the sound (AUX1-5) or addition of Lionel smoke fluid in order to resetting the engine (AUX1-0) will return the function. Pierce the fluid tube’s end with a smoke unit to the initial “OFF”...
Website at www.lionel.com. consumer-purchaser, for one year against original If you prefer to send it back to Lionel L.L.C. for defects in materials or workmanship when pur- factory repair, you must first call 810-949-4100 or chased through an authorized Lionel merchant.
Need help?
Do you have a question about the Pennsylvania Railroad 4-4-4-4 T1 Duplex and is the answer not in the manual?
Questions and answers