Table of Contents
Advertisement
7. "PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
DESCALING": Place an empty container with a minimum
capacity of 2 litres under the hot water/steam spout (C6)
and coffee spouts (A8) (fig. 8);
Important! Danger of burns
Hot water containing acid flows out of the hot water/steam
spout. Take care to avoid contact with splashes of this solution.
8. Press "
OK" to confirm that you have added the des-
caling solution. "DESCALING UNDERWAY" appears on the
display. The descale programme starts and the descaler
liquid comes out of the hot water/steam and coffee spouts.
A series of rinses and pauses is performed automatically to
remove all the scale residues inside the coffee machine;
After about 25 minutes, descaling stops;
9. "RINSE AND FILL WATER TANK UP TO MAX LEVEL" (fig. 5):
the appliance is now ready to rinse with fresh water. Empty
the container used to collect the descaler solution. Extract
the water tank, empty, rinse under running water, fill
with fresh water up to the MAX level and put back in the
appliance;
10. "PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING": Place the container used to collect the descaler
solution empty under the coffee spouts and hot water/
steam spout (fig. 8) and press "
11. Hot water is delivered first from the coffee spouts, then
from the hot water/steam spout and "RINSING UNDERWAY"
is displayed;
12. When the water in the tank has run out, empty the con-
tainer used to collect the rinsing water;
48
48
48 8 8 8 8 8
15. "INSERT WATER TANK" (fig. 6): Put the water tank back in the
appliance;
16. "PLACE 2l CONTAINER UNDER SPOUTS PRESS OK TO START
RINSING": Place the container used to collect the descaler
solution empty under the hot water/steam spout (fig. 8)
and press "
OK" ;
OK" ;
13. "INSERT FILTER INTO ITS
HOUSING" (fig. 48). Press
"
NEXT" and extract
the water tank. Replace
the water softener filter if
removed previously;
14. "RINSE AND FILL WATER
TANK UP TO MAX LEVEL"
(fig. 5): Fill the tank up to
the MAX level with fresh
water;
17. Hot water is delivered from the hot water/steam spout and
"RINSING UNDERWAY" is displayed;
18. "EMPTY DRIP TRAY" (fig. 45): At the end of rinsing, remove,
empty and replace the drip tray (A14) and grounds con-
tainer (A10). Press "
18. "DESCALE COMPLETE": press "
19. "FILL TANK WITH FRESH WATER": empty the container used
to collect the rinse water, remove the water tank and fill
with fresh water up to the MAX level, then put back in the
appliance.
Descaling is complete.
Please note!
•
If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
•
After descaling, it is normal for the grounds container
(A10) to contain water.
18.
SETTING WATER HARDNESS
The "DESCALE" message is displayed after a period of time es-
tablished according to water hardness.
The machine is set by default for a hardness of "LEVEL 4". The
machine can also be programmed according to the hardness
of the mains water in the various regions so that the machine
needs to be descaled less often.
18.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
from its pack (attached to the English instructions).
2. Immerse the paper completely in a glass of water for one
second.
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level.
soft water
slightly hard water
hard water
very hard water
18.2 Setting water hardness
"
1. Press "
(B2) to enter the menu;
2. Press < (B10) or > (B8) until "
pears on the display (B);
22
NEXT";
OK";
WATER HARDNESS" ap-
Advertisement
Table of Contents
Troubleshooting
