Extron electronics DMP 128 Setup Manual page 4

Dante Network Audio Setup
The following is the recommended procedure for configuring DMP 128 AT models on a Dante network.
NOTE:
A connection to both the Dante (AT) Ethernet switch and the DMP 128 LAN port is required to follow this setup
procedure. If the control computer has only one Ethernet port, connect it to a rear panel AT port (item
connect a short CAT 5 cable from the LAN port (item
use an Ethernet switch to connect the control computer to both the LAN and AT ports.
Connect the control computer to an AT (Dante) port on the DMP 128. Also connect the control computer to the DMP 128 LAN
1.
port. (See "Note" above.)
Start DSP Configurator in Live mode (see steps 1, 2, and 3b of
2.
From the DSP Configurator menu bar, select Tools, then select Device Settings.
3.
In the Unit Name: box, enter a descriptive name for the DMP 128 (typically the device name and location) that enables it to
4.
be easily identified on the network.
Click Apply, then close the dialog box.
5.
From the DSP Configurator menu bar, select Network Audio Control. If Dante Controller does not launch, see the
6.
Controller Software Installation
Using Dante Controller, from the menu bar, select Device>Device View.
7.
Choose the Dante device. The DMP 128 will appear as DMP128, plus the last six digits of the Dante MAC address.
8.
NOTE:
Connect DMP 128 units to the Dante network one at a time to easily identify which one is being named. To
confirm the proper device is being configured, compare the Dante MAC address printed on the rear of the unit with the
MAC address in the Device View..
Select the Device Config tab in Dante Controller.
9.
Rename the device to match the DSP 128 name given in DSP Configurator (see step 4 above), then press enter.
10.
Select Yes to confirm the new name.
11.
To connect additional DMP 128s, repeat this procedure with the next device.
12.
See the Dante Controller section in the DMP 128 User Guide for operation of the controller software.
Telephone Ports (DMP 128 C P and DMP 128 C P AT only)
The DMP 128 provides a telephone interface with separate input and output signal processing paths (labeled "Telephone Rx"
and "Telephone Tx" on the DSP Configurator main screen on the previous page). The country code must be entered before
attaching the DMP 128 to a phone system.
To set or change the country code of the phone model:
Follow Steps 1 and 2 from
1.
select Live in the Mode box.
NOTE:
The device settings dialog can only be accessed in live mode and
only when the DMP 128 is connected to the control computer using the LAN
port. RS-232 and USB connection cannot be used to access the phone
dialer.
From the main DSP Configurator toolbar, select Tools, then select Device Settings.
2.
From the Device Settings dialog, select the Phone Settings tab (see diagram at
3.
right).
If the correct country code is not listed after the "Selected Country:", click Change
4.
Phone's Country Code, then select the correct country code for your region from the
dropdown list.
Click Apply, then close the dialog boxes.
5.
See the DMP 128 User Guide for operating details of the phone modem.
Extron Headquarters
+800.633.9876 Inside USA/Canada Only
Extron USA - West Extron USA - East
+1.714.491.1500 +1.919.850.1000
+1.714.491.1517 FAX +1.919.850.1001 FAX
4
©
2013 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners.
ç
section (previous section).
"To Configure the DMP 128"
Extron Europe Extron Asia
+800.3987.6673 +800.7339.8766
Inside Europe Only Inside Asia Only
+31.33.453.4040 +65.6383.4400
+31.33.453.4050 FAX +65.6383.4664 FAX
on page 2) to an unused AT port (item
DMP 128 Configuration, above).
on the previous page, then
Extron Japan Extron China
+4000.EXTRON
+4000.398766
+81.3.3511.7655
Inside China Only
+81.3.3511.7656 FAX
+86.21.3760.1568
+86.21.3760.1566 FAX
j on page 2). Then
j on page 2). Alternately
Extron Middle East Extron Korea
+971.4.299.1800 +82.2.3444.1571
+971.4.299.1880 FAX +82.2.3444.1575 FAX
www.extron.com
Dante
Extron India
1800.3070.3777
Inside India Only
+91.80.3055.3777
+91.80.3055.3737 FAX
68-2036-50
Rev. B 02 13