Hitachi WH 14DAF2 Handling Instructions Manual
Cordless impact driver
Hide thumbs
Also See for WH 14DAF2:
- Safety and instruction manual (68 pages) ,
- Handling instructions manual (25 pages) ,
- Technical data and service manual (31 pages)
Related Manuals for Hitachi WH 14DAF2
Summary of Contents for Hitachi WH 14DAF2
- Page 1 Cordless Impact Driver WH 14DAF2 Read through carefully and understand these instructions before use. Handling instructions...
-
Page 2: General Power Tool Safety Warnings
d) Do not abuse the cord. Never use the cord for Symbols carrying, pulling or unplugging the power tool. WARNING Keep cord away from heat, oil, sharp edges or The following show symbols used for moving parts. the machine. Be sure that you Damaged or entangled cords increase the risk understand their meaning before use. - Page 3 d) Store idle power tools out of the reach of children PRECAUTIONS FOR CORDLESS IMPACT and do not allow persons unfamiliar with the DRIVER power tool or these instructions to operate the power tool. This is portable tool for tightening and loosenig Power tools are dangerous in the hands of screws.
-
Page 4: Specifications
SPECIFICATIONS POWER TOOL Model WH14DAF2 No-load speed 0 – 2500 min –1 Capacity M4 – M8 (Small screw) M5 – M12 (Ordinary bolt) M5 – M10 (High tension bolt) Tightening torque Maximum 120 N·m {1220 kgf·cm} Tightening is M14 high tension bolt (strength grade 12.9), when fully charged at 20°C temp. -
Page 5: Prior To Operation
When the pilot lamp does not go off even if more than 120 minutes have elapsed after starting of the Handle charging, stop the charging and contact your HITACHI AUTHORIZED SERVICE CENTER. CAUTION If the battery is heated due to direct sunlight, etc.,... -
Page 6: How To Use
Movement Driver Hexagonal Loosen hole in the Guide anvil sleeve Fig. 5 Fig. 3 CAUTION: (b) Remove the hook and spring. (Fig. 6) If the guide sleeve does not return to its original position, then the bit is not installed properly. HOW TO USE CAUTION: When using the light equipped hook, pay sufficient... - Page 7 CAUTION: Remove exhausted batteries from the hook Do not look directly into the light. immediately. Such actions could result in eye injury. Do not discard batteries together with normal trash (4) Replacing the batteries and do not throw batteries into fire. (a) Loosen the hook screw with a phillips-head Store batteries out of the reach of children.
-
Page 8: Operational Cautions
5. Work at a tightening torque suitable for the bolt OPERATIONAL CAUTIONS under impact The optimum tightening torque for nuts or bolts differs 1. Resting the unit after continuous work with material and size of the nuts or bolts. An After use for continuous bolt-tightening work, rest excessively large tightening torque for a small bolt the unit for 15 minutes or so when replacing the... -
Page 9: Maintenance And Inspection
D : Remarks Uncertainty K = 1.5 m/s CAUTION: Repair, modification and inspection of Hitachi Power Tools must be carried out by an Hitachi Authorized WARNING Service Center. The vibration emission value during actual use of the This Parts List will be helpful if presented with the... -
Page 11: Guarantee Certificate
GUARANTEE CERTIFICATE 1 Model No. 2 Serial No. 3 Date of Purchase 4 Customer Name and Address 5 Dealer Name and Address (Please stamp dealer name and address) - Page 16 EN60745, EN60335, EN55014 and EN61000 in accordance with Council Directives 2004/108/EC, 2006/95/EC and 98/37/EC. This declaration is applicable to the product affixed CE marking. Representative office in Europe Hitachi Power Tools Europe GmbH 30. 1. 2009 Siemensring 34, 47877 Willich 1, F. R. Germany Head office in Japan Hitachi Koki Co., Ltd.