Table of Contents
Advertisement
Chapter 7
Split Mode
Creating a Split allows you to divide the Andante CGP220 keyboard into an upper and lower
region. For example, you can create a split and play a Piano Voice with the right hand and a
Bass Voice with the left hand.
Split Mode Navigation Buttons
Depending on the selected parameter and the current mode, some buttons operate differently.
The following is a description of the Split Mode navigation buttons.
▲
▼
Select
Buttons
and
Use these buttons to step through the parameters.
Prev- and +Next Buttons
For the Split Voice parameter, use these buttons to step through the category voices. In Split Key, Split
Volume or Split Transposition, use these buttons to increase or decrease a value.
Category Button
In Split Voice, use this button to select another category; it acts the same as it would in Voice Mode. If
the Split Key, Split Volume or Split Transition parameter is active, pressing a category button returns the
Andante CGP220 to the Split Voice parameter.
Selecting Split Mode Voices
Select the voice you want to use as your primary voice. Press the Split button to enter Split Mode. The Split button
is located on the left side of the front panel.
When the Split button is pressed, the current voice becomes the primary (right hand) split
voice.
The default secondary voice ID is 105, P Bass, and the default split key is F#3, or the last
settings selected since the instrument was switched on.
To exit Split Mode, press the Split button again.
Split Mode Parameters
There are four parameters available in Split Mode:
● Secondary or "Left Hand" Voice
● Split Key Position
● Split Volume Balance
● Secondary or "Left Hand" Octave Change
In Split Mode, use the Select▲ and ▼ buttons to step through the parameters. Press the Prev- or +Next buttons
to make your changes to that parameter.
page 18
Split Voice Change for Secondary or Left Hand
Split
Press the Split button, and the secondary voice parameter is selected. The default secondary voice
is 105, P Bass, or the last secondary voice selected since the instrument was switched on. To choose
a different voice as the secondary voice, press the category voice you desire, then press the Prev- or
+Next buttons to advance to your selected sound. The new sound will now become your default "left
hand" or secondary voice.
Pressing the Prev- / +Next button pair will reset to the factory default voice setting.
Changing Split Key
In Split Mode, press the Select ▲ button until you see the display
KEY:F#3 (the default split key setting is F#3, or the last setting select-
ed since the instrument was switched on). The split key is the highest
key of the secondary voice. Press the Prev- or +Next buttons to
change the position of the split key. Pressing the +Next button will
take you to the next highest key. Pressing the Prev- button will take
you down a step. You can select any split point across all 88 keys
from A0 to C8.
Pressing the Prev- / +Next button pair will reset the F#3 factory default split.
Balance Split Volume
This parameter sets the volume between the two split sounds.
In Split Mode, press the Select▲button until you arrive at the screen
display VOL:0. This is the Split Balance Volume. Press the Prev- button
from -1 to -9 to decrease the volume of the secondary voice (left hand).
Press the +Next button from +1 to +9 to decrease the volume for the
primary voice (right hand). The value range of this parameter is -9 to
+9. The default Split Volume is 0, or the last setting selected since the
instrument was switched on.
Pressing the Prev- / +Next button pair will reset back to the factory default split volume.
Split Octave Transposition
This parameter sets the transposition of the secondary voice relative to the primary voice.
In Split Mode, press the Select ▲ button, until the screen displays
XPOSE:12 ST. (The default setting is 12 ST, or the last setting selected
since the instrument was switched on.) Press the Prev- or Next+
button to change octaves for the left hand or the secondary voice.
Pressing the Prev- / +Next button pair will reset the octave back to
12, the factory default setting
Chapter 7
Split Mode
KEY: F#3
VOL: 0
XPOSE: 12
page 19
Advertisement
Table of Contents
