Table of Contents
Advertisement
2
User's Manual for
Answering System 1305
Fold open this manual for information about this product's
installation and operation. Please read Part 1 – Important
Product Information, included in this package.
Part 2
© 1998 Philips Consumer Communications L.P. All rights reserved.
Printed in China. 848230066 Issue 1AT&T
Advertisement
Table of Contents
Related Manuals for AT&T 1305
Summary of Contents for AT&T 1305
-
Page 1: Answering System
User’s Manual for Answering System 1305 Fold open this manual for information about this product’s installation and operation. Please read Part 1 – Important Product Information, included in this package. Part 2 © 1998 Philips Consumer Communications L.P. All rights reserved. -
Page 2: Installation
I N S T A L L A T I O N Insert the microcassette. Slide the cover down and insert the microcassette with the full reel at the bottom. Replace the cover. Connect the line cord. Plug the line cord into a modular wall jack. Standard Electrical Outlet... -
Page 3: Recording Your Announcement
O P E R A T I O N Recording Your Announcement Before using this answering system, you need to record the announcement (up to one minute long) that callers will hear when the system answers a call. For best results, record your announcement in a quiet environment, without “background”... -
Page 4: Turning The System On Or Off
O P E R A T I O N Press and hold A for two seconds, then release the button and wait for the system to beep. After the beep, speak toward the microphone, from about nine inches away. Press and release p, when you are finished. The tape resets automatically and plays the announcement, and the MESSAGE light goes To review your announcement —... -
Page 5: Priority Call Signal
O P E R A T I O N Priority Call Signal When a caller enters the Priority Calling Code from a touch tone phone, the system beeps loudly to alert you that you have a priority call. You’ll need to provide select callers with the Priority Calling Code (preset to 1235) in order for them to use this feature. -
Page 6: Volume Control
O P E R A T I O N Volume Control This system has eight volume levels; each time you press the appropriate button, the volume increases or decreases one level. To increase volume, press and release +. To decrease volume, press and release -. If you’re adjusting the volume while the system is not playing messages, you’ll hear a beep each time you change the volume level. - Page 7 O P E R A T I O N If you wish, press and release f to fast forward while the memo is playing — OR — Press and release — OR — Press and release p to pause. Two-Way Recording You can record a phone conversation (the length of the recording depends on the length of your microcassette).
- Page 8 O P E R A T I O N When the Tape is Full When the recording side of the tape is completely full, the system beeps, the MESSAGE light flashes rapidly, and the system turns itself off because it cannot record a caller’s message.
-
Page 9: Remote Access Code
R E M O T E Remote Access Code You can use many features of this answering system remotely from a touch tone phone. Most features can be accessed only after you enter a Remote Access Code. (The preset Remote Access Code is printed on the label on the bottom of the answering system.) Connect with the Answering System and Listen to Messages Dial your telephone number from a touch tone phone. -
Page 10: Room Monitor
R E M O T E Room Monitor You can call the answering system and listen to any activity in the room for 15 seconds. Connect with the answering system and listen to messages. Press 3 3. You can listen after the beep. After 15 seconds, the system exits Room Monitor and beeps twice. -
Page 11: In Case Of Difficulty
I N C A S E O F D I F F I C U L T Y If this answering system does not work properly, try the following suggestions. If you’re still having difficulty, call 1 800 722–9125. If the MESSAGE light flashes rapidly: •... - Page 12 I N C A S E O F D I F F I C U L T Y If the system does not respond to remote commands: • Make sure you are calling from a touch tone telephone. If you hear clicks when you dial, the phone is not a touch tone phone.
- Page 13 Answering System 1305 From a Remote Touch Tone Phone To connect with your answering system: 1 Dial your telephone number from a touch tone phone. 2 When the system answers, press * * during the announcement, then enter your four-digit Remote Access Code.
- Page 14 COMMAND Rewind Fast Forward Save all messages Clear all messages Pause/Stop Change Remote Access Code Play/Stop Announcement Record/Stop Announcement 5 5 Room Monitor Turn system on Turn system off COMMAND Rewind Fast Forward Save all messages Clear all messages Pause/Stop Change Remote Access Code Play/Stop Announcement...
Need help?
Do you have a question about the 1305 and is the answer not in the manual?
Questions and answers