Page 1
Instructions for use SKF TLGB 20 Series “A” July 2015 Date of issue D a n g e r Form number MP5456 Read manual prior to installation or use of this product. Keep manual nearby for future reference. Failure to follow instructions and safety precautions may result in death or serious injury.
The SKF battery driven grease gun tool will increase the risk of electric shock. facilities, ensure these are connected TLGB 20 was exclusively designed to pump • Do not abuse the cord . never use the and properly used . Use of these devices...
W a r n I n g • recharge only with the battery charger specified by the manufacturer . Use only SKF TLGB 20-3 high pressure hose Do not use any hose that has not been A charger that is suitable for one type of 900 mm (36 in.) with coupler.
Designed to operate over a long period of ed in the technical data and the declaration time, with a minimum of maintenance. Should you find one day that your SKF of conformity have been measured in Continuous satisfactory operation depends...
This manual contains important safety and other liquids. This may cause premature operating instruction for the SKF TLGB cell failure. 20-5 and SKF TLGB 20-6 battery chargers. Failure to comply may result in seri- ous injury or death. D a n g e r Do not probe with conductive objects.
20-5 and TLGB 20-6 chargers should tures could cause personal injury or fire. replaced by the manufacturer or an only be used to charge SKF TLGB 20-2 • This appliance is not intended for use by authorized SKF service center in order to battery packs.
Tool use and care Specifications SKF battery driven grease gun TLGB 20 Do not continue to hold down trigger if grease gun is stalled. This could damage the Operating power 14,5 to 20 V DC motor or cause fire. Maximum operating pressure:...
General description Inspection The SKF TLGB 20 is a lithium-ion battery Visually inspect for damaged, loose or operated grease gun and was developed for missing parts. If equipment is worn or dam- manual lubrication of grease points including aged, remove from service. Contact an...
TLGB 20 Set up Prime the grease gun 7 Using follower handle (12), release fol- lower rod from slot. Prime the cordless grease gun after each Install/replace grease 8 Purge air from grease tube by unscrewing refill or grease cartridge change.
Operation Fig . 3 Display and light To turn display (5) “on”, either: • Push button “1” (4) († fig . 3) • Squeeze the trigger/switch. To turn light “on/off”: • Push button “1” (4). Display and light shut off automatically after 30 seconds if gun is not operating.
Refilling options To fill gun with filler pump Expelling air pockets 1 Engage the follower rod with the follower (air purging) To fill gun from bulk container by rotating the follower handle. 2 Insert the gun bulk fill valve into the filler 1 Withdraw the follower rod from the 1 Remove pump assembly from grease pump socket.
Always unplug the SKF chargers are designed to charge SKF charger from the power supply when lithium-ion batteries in 30 to 90 minutes there is no battery in the cavity. Unplug Notice depending on the battery’s state of charge...
Service parts/kits list Item Description Part number Grease tube assembly TLGB 20-4 Flexible hose kit TLGB 20-3 Coupling Flexible hose 36 in. (914 mm) with gasket Battery pack 20 V (lithium) TLGB 20-2 Battery charger (lithium) 220-240 volt TLGB 20-5...
Page 16
SKF’s global footprint provides SKF customers with uniform quality standards For inclusion in the SKF BeyondZero portfolio, a product, service or solution and worldwide product availability. Our local presence provides direct access must deliver significant environmental benefits without serious to the experience, knowledge and ingenuity of SKF people.
Need help?
Do you have a question about the TLGB 20 and is the answer not in the manual?
Questions and answers