Page 1
5300 Automatic Scrubber Model No.: Operator and Parts Manual 300000PAC 300000 603053 606445 173420 Rev. 07 (11- -04) Home Find... Go To..
Page 2
Serial No.- supplies may be ordered by phone or mail from any authorized parts and service center, distributor or from E1995, 1999, 2000, 2001, 2002, 2004 Tennant Company any of the manufacturer’s subsidiaries. Printed in U.S.A This machine will provide excellent service. However, Specifications and parts are subject to change without notice.
WARNING: Spinning Brush. Keep Hands All repairs must be performed by a Away. Turn Off Power Before Working On qualified service person. Machine. Do not modify the machine from its original design. Tennant 5300 (11- -04) Home Find... Go To..
FOR SAFETY: Do not operate machine unless operator manual is read and understood. MOVING PARTS LABEL - - Located on scrub head WARNING: Spinning Brush. Keep Hands Away. Turn Off Power Before Working On Machine. Tennant 5300 (11- -04) Home Find... Go To..
E. Solution Tank Fill Opening M. Scrub Head Lift Pedal F. Batteries N. Squeegee Down Pressure Knob G. Recovery Tank Cover O. Squeegee Leveling Knob H. Solution Tank Hose P . Scrub Head Release Pedal Tennant 5300 (11- -04) Home Find... Go To..
Q. Solution Tank Hose G. Pump On Light (Option) R. Recovery Tank Drain Hose H. ES (Extended Scrub) Switch (Option) S. Squeegee Lever Power Wand Switch (Option) T. Charger Plug J. Hourmeter (Option) Tennant 5300 (11- -04) Home Find... Go To..
NOTE: The reading on the battery discharge indicator is not accurate when the machine is first powered on. Operate the machine a few minutes before reading the charge level of the batteries. Tennant 5300 (11- -04) Home Find... Go To..
Start: Press the top of the solution switch. The switch will light up. NOTE: Stop the solution flow just before turning a corner. Then start the solution flow once around the corner. Stop: Press the bottom of the solution switch. Tennant 5300 (11- -04) Home Find... Go To..
Off: Press the left side of the ES switch. POWER WAND SWITCH (OPTION) On: Turn the key to the right. The power wand switch turns on and off the power wand solution system. Off: Turn the key to the left. Tennant 5300 (11- -04) Home Find... Go To..
Never substitute higher value fuses than specified. Increase: Turn the solution knob counter-clockwise. The more you turn the knob, the more you increase the solution flow to the floor. Decrease: Turn the solution knob clockwise. Tennant 5300 (11- -04) Home Find... Go To..
The drain hose is plugged by placing the cap on the end of the hose and turning clockwise to tighten the cap. Tennant 5300 (11- -04) Home Find... Go To..
To adjust the squeegee deflection along the entire width of the squeegee see ADJUSTING SQUEEGEE BLADE DEFLECTION in the Maintenance section. Tennant 5300 (11- -04) Home Find... Go To..
5. Check battery discharge indicator. Machine must 178 mm (7 in) W x 381 mm (15 in) L x 372 mm be in full operation for accurate reading (See (14.63 in) H. MACHINE OPERATION). Charge batteries if necessary. Tennant 5300 (11- -04) Home Find... Go To..
- Check the squeegee for proper deflection. Check the squeegee blade for wear, rounded edges, FOR SAFETY: Before leaving or servicing nicks, or cuts. machine, stop on level surface and turn off machine. 3. Turn the machine power off. Tennant 5300 (11- -04) Home Find... Go To..
ATTENTION: Use only recommended detergents. Machine damage due to improper detergent usage will void the manufacturer’s warranty. Contact your Tennant Sales Representative for detergent Plan the scrubbing in advance. Try to arrange long recommendations. runs with minimum stopping and starting. Do an NOTE: Floor conditions, water condition, amount of entire floor or section at one time.
Page 18
Do Not Pick Up Flammable Materials Or Reactive lever. Metals. 8. Adjust the solution flow to the floor as needed. 5. Start the solution flow with the solution switch. 9. Adjust brush pressure for cleaning application. Tennant 5300 (11- -04) Home Find... Go To..
1. Stop scrubbing. 2. Drive the machine next to a floor drain or sink. 3. Turn the solution switch off. Propel the machine forward to pick up any solution left on the floor. Tennant 5300 (11- -04) Home Find... Go To..
Page 20
NOTE: If using a bucket to drain machine, do not use same bucket for filling solution tank. This will prevent possible solution line clogs. Tennant 5300 (11- -04) Home Find... Go To..
Page 21
(140_F) or tank damage may occur. Do not use steam to clean the tank. NOTE: If using a bucket to drain machine, do not use same bucket for filling solution tank. This will prevent possible solution line clogs. Tennant 5300 (11- -04) Home Find... Go To..
2. Turn the machine power off. - Check the squeegee for wear or damage. FOR SAFETY: Before leaving or servicing machine, stop on level surface and turn off machine. Tennant 5300 (11- -04) Home Find... Go To..
CHARGER TYPE: FOR LEAD ACID BATTERIES OUTPUT VOLTAGE - 24 VOLTS OUTPUT CURRENT - 12 AMPS for 130 AH Batteries OUTPUT CURRENT - 20 AMPS for 215 AH Batteries AUTOMATIC SHUTOFF CIRCUIT FOR DEEP CYCLE BATTERY CHARGING Tennant 5300 (11- -04) Home Find... Go To..
DO NOT OVERFILL. of the squeegee. 3. Put together the wand and the wand hose. 4. Connect the vacuum wand hose and the squeegee suction hose with the adapter. Tennant 5300 (11- -04) Home Find... Go To..
Page 25
11. Reconnect the squeegee suction hose to the top of the squeegee. 7. Vacuum the floor. 8. When finished, raise the squeegee to shut off the vacuum. Tennant 5300 (11- -04) Home Find... Go To..
4. Attach the end of solution hose to the quick-disconnect. Push the connector in until it stops. Pull on the hose to make sure it is connected. Tennant 5300 (11- -04) Home Find... Go To..
Page 27
If the cleaning tool is hard to push, or is not picking up the solution very well, adjust the roller wheels on the tool by turning the black adjustment knob. 14. Remove the vacuum hose from the squeegee suction hose. Tennant 5300 (11- -04) Home Find... Go To..
4. Remove and clean pads or brushes. Never use soiled pads when cleaning. Replace pads when they become loaded with residue. Replace brush if needed (See REPLACING THE SCRUB BRUSH). Tennant 5300 (11- -04) Home Find... Go To..
Check the hydrometer readings against the 3. Check for loose battery cable connections. following chart to determine the remaining battery 4. Lubricate caster grease fitting with a water charge level. resistant grease. Tennant 5300 (11- -04) Home Find... Go To..
4. Keep the battery tops clean to prevent battery 2. Lower the scrub head. corrosion. 3. Check to see if the scrub head skirt touches the To clean batteries: floor all the way around the scrub head. Tennant 5300 (11- -04) Home Find... Go To..
4. Turn the brush until you can see the brush drive machine, stop on level surface and turn off pin. machine. 2. Raise the scrub head. 3. Loosen the skirt band clamp. Tennant 5300 (11- -04) Home Find... Go To..
9. Make sure one of the drive pin slots can be seen through the access opening. FOR SAFETY: Before leaving or servicing machine, stop on level surface and turn off machine. 2. Raise the squeegee. Tennant 5300 (11- -04) Home Find... Go To..
To adjust squeegee deflection, see ADJUSTING SQUEEGEE 1. Turn the machine power on. DEFLECTION. 2. Lower the squeegee. 3. Drive the machine forward, then turn the machine power off. Tennant 5300 (11- -04) Home Find... Go To..
5. To adjust the blade deflection, loosen the nut that secures the squeegee support wheel. Once loosened, the wheel can be adjusted within the slot on the wheel mounting bracket. Raise wheel to increase deflection or lower to decrease. Tennant 5300 (11- -04) Home Find... Go To..
You can jack up the machine for servicing anywhere under the solution tank. Use a piece of wood to distribute the machine weight load. Tennant 5300 (11- -04) Home Find... Go To..
5. The washer solution does not need to be drained from the solution tank. MACHINE DIMENSIONS 724 mm 1181 mm (28.5 in.) (46.5 in.) 984 mm (38.75 in.) 508 mm (20 in.) Tennant 5300 (11- -04) Home Find... Go To..
Turn ES switch on. off. Poor scrubbing performance. Debris caught on scrub brushes. Remove debris. Improper detergent, brush, or pad used. Check with TENNANT representative for advice. Worn scrub brush or pad. Replace scrub brush or pad. Scrub brush motor circuit breaker Reset circuit breaker.
Vacuum fan 0.56 (0.75) Drive 0.15 (0.20) Type Phase Chargers TIRES Location Type Size Front (2) Wheels Solid, non-marking 8 x 2 in Rear (1) Casters Solid, non-marking 4 x 1.38 in Tennant 5300 (11- -04) Home Find... Go To..
Page 39
OPERATION Tennant 5300 (11- -04) Home Find... Go To..
PARTS LIST SOLUTION TANK AND VACUUM MOTOR GROUP Tennant 5300 (11- -04) Home Find... Go To..
Page 45
WASHER, LOCK, INT, #10, SS 630508 O- -RING, 9.2 ID X 12.7 OD 578201000 SCREW, 10- -32X.5 19066 WASHER, FLAT, #10 578301 KNOB, FILL- -COVER ∇ ASSEMBLY INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Tennant 5300 (11- -04) Home Find... Go To..
HEAD, WAND 579135 SCREW, SELF TD UNITED 579102 DBRUSH, WAND (TWO ROW) 579103 RETAINER, WAND BLADE 579187 CLIP, SPRING 579109 WAND, SINGLE BEND ∇ ASSEMBLY INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Tennant 5300 (11- -04) Home Find... Go To..
FITTING, 1/8M PLUG 579137 DFITTING, TIP, 9508 1/8V JET 579109 WAND, SINGLE BEND 579113 SWIVEL, WAND ATTACHMENT 150510 FITTING, 1/4F X 1/4H BARB ∇ ASSEMBLY INCLUDED IN ASSEMBLY D RECOMMENDED STOCK ITEMS Tennant 5300 (11- -04) Home Find... Go To..
Need help?
Do you have a question about the 300000PAC and is the answer not in the manual?
Questions and answers