Miller Electric CBI 801D Owner's Manual page 27

Table 7-3. Approximate Air Consumption (Cubic Feet) Required To Operate Various Pneumatic
MISCELLANEOUS
Compressed Air Consumption (CF)
PORTABLE
TOOLS
9 sec
Drill, 1/18" to 3/8" 3.75
Drill, 3/8" to 5/16" 5.25
Screwdriver,
#2 to #6 Screw
Screwdriver,
#6 to 5/16" Screw
Tapper, to 3/8"
Nutsetters, to 3/8"
Nutsetters, to 3/4"
Impact Wrench, 1/4" 2.25
Impact Wrench, 3/8"
Impact Wrench, 5/8"
Impact Wrench, 3/4" 5.25
Impact Wrench, 1" 6.75
Impact Wrench, 1-1/4" 8.25
Die Grinder, Small 2.25
Die Grinder, Medium
Horizontal Grinder, 2"
Horizontal Grinder, 4"
Horizontal Grinder, 6"
Horizontal Grinder, 8" 12.0
Vertical Grinders and
Sanders, 5" Pad 5.25
Vertical Grinders and
Sanders, 7" Pad
Vertical Grinders and
Sanders, 9" Pad 10.5
Burring Toll, Small 2.25
Always check with tool manufacturers for actual air consumption of tools being used. The above is based on averages and should not be
considered accurate for any particular make of tool.
Above tools are rated based upon typical "on-load" performance characteristics.
For other values, adjust the C.F. air consumption on a proportional basis.
The cubic feet (C.F.) air consumption for 1 minute may also be expressed as air consumption in cubic feet per minute (C.F.M.)
OM-166 941 Page 22
Equipment At Pressure Range 70-90 P.S.I.G.
Percent Use Factor And
15 sec 21 sec
6.25 8.75
8.75 12.25
1.8 3.0 4.2
3.6 6.0 8.4
3.0 5.0 7.0
3.6 6.0 8.4
4.5 7.5 10.5
3.75 5.3
3.0 5.0 7.0
4.5 7.5 10.5
8.75 12.25
11.25 15.75
13.75 19.2
3.75 5.3
3.6 6.0 8.4
3.0 5.0 7.0
9.0 15.0 21.0
9.0 15.0 21.0
20.0 28.0
8.75 12.25
9.0 15.0 21.0
17.5 24.5
3.75 5.3
MISCELLANEOUS
PORTABLE
TOOLS
1 min
25 Burring Tool, Large
35 Rammers, Small
12 Rammers, Medium
24 Rammers, Large
20 Backfill Tamper
24 Compression Riveter
30 Air Motor,
1 Horsepower
15 Air Motor,
2 Horsepower
20 Air Motor,
3 Horsepower
30
Air Motor Hoist
35 1000#
45 Air Motor Hoist,
2000#
55
Paint Spray Gun
15 (Production)
24 HAMMERS
20 Scaling Hammer
60 Chipping Hammer
60 Riveting Hammer,
Light
80 Riveting Hammer,
Heavy
35 SAWS
Circular, 8"
60
Circular, 12"
70 Chain, Lightweight
15 Chain, Heavy Duty
Percent Use Factor And
Compressed Air Consumption (CF)
9 sec 15 sec 21 sec
3.6 6.0 8.4
3.9 3.25 9.1
5.1 8.5 11.9
6.0 10.0 14.0
3.75 6.25 8.75
0.2 cu. ft. per cycle
3.75 6.3 8.75
7.5 12.5 17.5
11.25 18.75 26.3
1 cu. ft. per foot of lift
1 cu. ft. per foot of lift
3.0 5.00 7.00
1.3 3.0 4.2
4.5 7.5 10.5
2.25 3.75 5.25
4.5 7.5 10.5
6.75 11.25 15.75
9.75 16.25 23.8
4.20 7.0 9.8
13.1 21.8 30.5
1 min
24
13
34
40
25
25
50
75
20
12
30
15
30
45
65
28
87