Advertisement
7
Check that all parts were
n
installed. If there is an extra part,
go back through the steps to see which
step was skipped.
8
n
Check that you have all your tools.
9
Take a few minutes to read the
n
Use and Care Guide so you can
get the best use from your new
portable dishwasher. Then move the
;tu;zsdher
to the location where it will
--
YiiJ :.-
1.
faucet
.....'.'z
adapter
*
10
Turn on the hot water faucet
H until water is hot. Turn the
faucet off. Pull the inlet/drain
hose from
the storage compartment.
Attach the
hose connector
to the faucet by pulling
down on the locking collar while
pushing the connector
over the faucet
adapter. It will snap into place. Release
the locking collar.
11
Untape the power supply
H cord and plug it into the
grounded
outlet. Open the dishwasher
door and spin the spray arm to check
for movement.
Close the door.
12
Turn hot water faucet to
n
fully open position. Start
dishwasher.
13
Check for leaks around the
H door and mounting gasket,
and at the hose connections.
Product/Property
Damage
Turn water faucet off and press
bleeder button to release water
pressure before removing the drain
hose from faucet.
Failure to do so before removing
drain hose may result in product or
property damage.
faucet
,,,,........... . ..-.....""".
adapter
locking
collar-;---.- . . . . . . . . . . . . . . . . . . . . . . . .
. . . . .
. . . .
...
14
When the cycle is complete,
w unplug power supply cord and
push cord into storage compartment.
Turn the water faucet off. Press the red
button (bleeder button) on the
connector
to release the water
pressure. With one hand, move the
locking collar downward
while using
the other hand to pull down on the
connector.
Turn the connector
upside
down and empty any water remaining
inside the connector.
Check for
complete
drain (no water should
be visible).
15
Push hoses into storage
n
compartment.
Congratulations!
You have just finished installing
your new dishwasher. Keep
Installation Instructions available
for easy reference.
Converting to
built-in
Your portable dishwasher can be
converted
to a built-in (undercounter)
model by using conversion kit, Part No.
43 17856. The kit is available from your
dealer or authorized parts distributor.
Installation Instructions are included
with the kit.
To than e door
panel co 8 or
(For models so equipped.)
Personal Injury Hazard
Wear gloves and handle panels
carefully.
Cut metal edges may cause
personal injury or damage to other
materials.
1
Push up at each end of
n
retainer at bottom of door
panel. Then pull retainer toward you.
Set retainer aside.
2
Slide door
n
panel(s)
down to clear
console. Use both
hands to bow top
and bottom edge
of door panel(s).
Remove panel(s)
from door. Do Not
remove spacer.
I l--./I&q
3
With
n
desired
color facing out,
insert one side of
door panel(s)
into
one
side
of door
frame.
4
Bow door
n
panel(s)
and insert other
side of door
panel(s) into door
frame.
,,... control
console
5
Push in
n
on door
panel(s) near the
top and slide
panel(s) and
spacer up inside
bottom of control
console.
bwer door
frame
6
Lift up and hold panel(s)
n
and spacer l/4" above lower
door frame.
7
Insert retainer over lower edge of
n
door frame while holding door
panel(s) and spacer up.
8
Snap
.
retainer
down into
place. Push down
firmly along entire
length of retainer
to make sure
w
I
retainer is secure. Slide door panel(s)
down.
color..
,panel.&-kJy
9
Important: Run fingers along
.
bottom of retainer to check that
retainer is lower than the lower door
frame.
Panel C
Advertisement
