Before Using Scale; Facts You Should Know - Conair WW7010WC Instructions Manual

Before Using Scale

1. Set switch on the base of scale to measure in kg (kilograms) or lb (pounds).
2. Set scale on floor. Surface must be level for accurate operation and safety
Customizing Your
Weight Watchers® Body Fat Monitor
1. Tap center of scale platform with foot to activate digital display (display will
flash).
2. Wait for "0.0" to appear in display window.
3. You are now ready to input your personal data. Firmly press the SET button
located below the display.
Enter User Number
• P-01 will flash in display window
• Press UP or DOWN arrows to select your individual user
number (Ten user numbers available: P-01 through P-10)
• When selected user number appears in display, press SET
button to save user number
• The scale is now ready for you to enter your height
Set Height
• "Ht" (height) will flash in display window
• Press UP or DOWN arrows to scroll to your height
measurement
• Press SET button to save height
• The scale is now ready for you to enter your age
Set Age
• "Age" will flash in display window
• Press UP or DOWN arrows to scroll to your age
• Press SET button to save age
• The scale is now ready for you to enter your gender
Set Gender
• The gender icons will flash in display window
• Press UP or DOWN arrows to select male or female icon
• Press SET button to save gender
4. Your personal data has now been entered and stored. User number will display
for 2 seconds, height for 2 seconds, age for another 2 seconds, to confirm
the programming. If any of these data points were set incorrectly, just go
through the customization steps (1–3) again. The scale is now ready for you
to weigh yourself and read body fat and body water and BMI measurements.
Using Your Weight Watchers® Body Fat Monitor
Precautions for Use
CAUTION! Use of this device by persons with any electrical implant such as a heart
pacemaker, or by pregnant women, is not recommended.
1. Tap center of scale platform with foot to activate digital display (display will flash).
2. Wait for "0.0" to appear in display window.
3. Firmly press the USER button located below the display several times until your
user number appears. Note: The scale will automatically scroll through your
customized data, then 0.0 will be displayed.
4. Step onto the scale BAREFOOT, making sure the balls of your feet cover
both metal plates.
5. Weight will be displayed for 3 seconds. Remain on scale without moving!
6. Display will flash "b" and your BMI value.
7. Display will flash "L" and your BMI/Fitness level.
8. Display will flash "bF" and "LB" or "KG", followed by the weight of your body fat.
9. Display will flash "bF" and "%", followed by your body fat percentage.
10. Display will flash "H2O" and "%", followed by your body water percentage.
11. Scale will automatically turn off.
Please read on for further information on Body Fat, Body Water, BMI, and
BMI levels
Using The Weight-Only Mode
For weight-only mode, no personal data entry is necessary
1. Place scale on a flat, level surface.
2. Tap center of scale platform with foot to activate (display will flash).
3. Wait for "0.0" to appear in display window.
4. Step onto scale. Weight measurement will appear in display window.

Facts You Should Know

Your Weight Watchers scale is a precise measuring instrument that is most
accurate when weighing a stationary object. To ensure the most accurate readings
for 99% of your total body weight, always try to stand on the same area of the scale
platform and DO NOT MOVE. Should the weight on the scale exceed the scale's
capacity, you may see an error message "Err".
Electronic sensors are sensitive. Be careful not to drop or jar the scale. Place it
gently onto floor surface, and store where it will be protected from impact. The
scale is an electronic instrument and should never be submerged in water. Clean
with damp cloth and/or glass cleaner.
In the unlikely event that the scale battery malfunctions and needs to be replaced,
lift the snap on battery cover on the bottom of the scale and replace the old
battery with a 3V Lithium battery (CR2032).
Dispose of the old battery properly. Do not attempt to open the scale or to
remove any components. Servicing should be done by qualified technicians
only. See warranty information.