Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ubiquiti RocketDish LW RD-5G30-LW
Summary of Contents for Ubiquiti RocketDish LW RD-5G30-LW
- Page 1 airMAX 2x2 PtP Bridge ® Dish Antenna Model: RD-5G30-LW...
-
Page 2: Package Contents
(Qty. 2) Guide (M10, Qty. 2) TERMS OF USE: Ubiquiti radio devices must be professionally installed. Shielded Ethernet cable and earth grounding must be used as conditions of product warranty. TOUGHCable ™ is designed for outdoor installations. It is the customer’s responsibility to follow local country regulations, including operation within legal frequency channels, output power, and Dynamic Frequency Selection (DFS) requirements. -
Page 3: Installation Requirements
AC ground of the PoE. We recommend that you protect your networks from the most brutal environments and devastating ESD attacks with industrial-grade shielded Ethernet cable from Ubiquiti Networks. For more details, visit www.ubnt.com/toughcable Hardware Overview Protective Shroud... -
Page 4: Installation
Installation Important: Handle the Dish Reflector with care. Deformations in its shape may reduce the RocketDish's effectiveness. 1. Line up the alignment tabs of the Mounting Bracket with the alignment slots of the Dish Reflector. Insert the tabs and rotate the Mounting Bracket until they lock into place. Ensure that the antenna feed slot of the Note: Mounting Bracket lines up with the antenna feed slot... - Page 5 2. The Dish Reflector and Antenna Feed are keyed so the Antenna Feed can only be installed in a single orientation. Follow these steps: a. Remove the knob from the Antenna Feed. b. Line up the alignment pins of the Antenna Feed with the alignment holes of the Dish Reflector and Mounting Bracket.
- Page 6 3. To secure the Antenna Feed to the Dish Reflector: a. Replace the knob and tighten it by hand until the knob touches the surface of the Mounting Bracket. b. Use a wrench or channel lock pliers to tighten the knob an additional ¼...
- Page 7 4. Attach the Rocket to the Mounting Bracket. a. Align the mounting tabs on the back of the Rocket with the Rocket mount. b. Slide the Rocket down to lock it into place. 5. Attach the other end of the RF Cables to the RF connectors on the Rocket in this combination: H to Chain 1 and V to Chain 0.
- Page 8 6. Attach the Protective Shroud. a. Align the hash mark on the top of the shroud with the notch on the Dish Antenna. b. Rotate the shroud clockwise until it locks into place.
- Page 9 7. Attach two Hex Head Bolts, two Lock Washers, and two Flat Washers to the bottom of the Mounting Bracket. Ensure that there is a gap of 8 mm between each Flat Washer and the Mounting Bracket. Ensure that each Lock Washer is always Note: installed between the Hex Head Bolt and Flat Washer.
- Page 10 8. Attach the horizontal slot of the Support Arm to the Upper Pole Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer. Ensure that the degree settings are the same Note: on both arms of the Upper Pole Bracket. Degree markings facing outward 9.
- Page 11 10. Each M8x150 Carriage Bolt includes a serrated flange nut. Remove these and use them in the next step. 11. Attach one Pole Clamp to each pole bracket. a. Insert two M8x150 Carriage Bolts into each pole bracket. b. Slide the hole of a Pole Clamp over one bolt of each pole bracket.
- Page 12 12. Attach the Stabilizer Brackets to the pole just beneath the area where the RocketDish will be attached. Note: The pole-bracket assembly can accommodate a Ø 38 - 101 mm pole. a. Place one Stabilizer Bracket on each side of the pole. b.
- Page 13 13. Attach the pole-bracket assembly to the pole: a. Slide the slot of each Pole Clamp over the corresponding M8x150 Carriage Bolt. b. Tighten the serrated flange nuts of the bolts to secure the pole-bracket assembly to the pole. Proper slot orientation 25 N-m...
- Page 14 14. Lift the Dish Reflector and align the two lower Hex Head Bolts with the slots on the Lower Pole Bracket. Seat the bolts in the slots. 15. Attach each arm of the Upper Pole Bracket to the Mounting Bracket using a Hex Head Bolt, Lock Washer, and Flat Washer.
- Page 15 16. Before adjusting the tilt angle, ensure that the six Hex Head Bolts are loose enough to allow movement. If you cannot spin the washers freely by IMPORTANT: hand, then loosen the Hex Head Bolts until you can. 17. To adjust the tilt angle, turn the screw head of the Elevation Rod until the desired tilt is reached.
-
Page 16: Specifications
Specifications RocketDish RD-5G30-LW Dimensions 650 x 650 x386 mm (25.6 x 25.6 x 15.2") Weight 7.4 kg (16.31 lb) (Mount Included) Frequency 5.1 - 5.9 GHz Gain 30 dBi Max. VSWR 1.6:1 Wind Survivability 200 km/h (125 mph) Wind Loading 790 N @ 200 km/h (178 lbf @ 125 mph) Polarization Dual Linear... -
Page 17: Limited Warranty
(VI) has no original Ubiquiti MAC label, or is missing any other original Ubiquiti label(s); or (VII) has not been received by Ubiquiti within 30 days of issuance of the RMA. -
Page 18: Limitation Of Liability
SUBJECT TO LIMITATIONS, INTERRUPTIONS, DELAYS, CANCELLATIONS AND OTHER PROBLEMS INHERENT IN THE USE OF COMMUNICATIONS FACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES AND ITS AND THEIR THIRD PARTY PROVIDERS ARE NOT RESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS, CANCELLATIONS, DELIVERY FAILURES, DATA LOSS, CONTENT CORRUPTION, PACKET LOSS, OR OTHER DAMAGE RESULTING FROM ANY OF THE FOREGOING. - Page 19 Note Some countries, states and provinces do not allow exclusions of implied warranties or conditions, so the above exclusion may not apply to you. You may have other rights that vary from country to country, state to state, or province to province. Some countries, states and provinces do not allow the exclusion or limitation of liability for incidental or consequential damages, so the above limitation may not apply to you.
- Page 20 RoHS/WEEE Compliance Statement English European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams.
- Page 21 Español La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación.
-
Page 22: Declaration Of Conformity
UBIQUITI NETWORKS device, megfelel a vonatkozó alapvetõ [Hungarian] követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Íslenska Hér me l sir UBIQUITI NETWORKS yfir ví a UBIQUITI NETWORKS device, er í samræmi vi grunnkröfur og a rar kröfur, sem ger ar eru í [Icelandic] tilskipun 1999/5/EC. -
Page 23: Online Resources
[Swedish] egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG. Español Por medio de la presente UBIQUITI NETWORKS declara que el UBIQUITI NETWORKS device, cumple con los requisitos esenciales [Spanish] y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. - Page 24 . u b n t . c o m ©2014-2015 Ubiquiti Networks, Inc. All rights reserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti U logo, the Ubiquiti beam logo, airMAX, airOS, Rocket, RocketDish, and TOUGHCable are trademarks or registered trademarks of Ubiquiti Networks, Inc.