IMPORTANT SAFETY INSTRUCTIONS This appliance is intended for residential use only. Only use the appliance for its intended purpose. The manufacturer cannot be held responsible for damages caused by improper use of this oven. This appliance complies with current safety requirements. Improper use of the appliance can lead to personal injury and material damage.
IMPORTANT SAFETY INSTRUCTIONS Installation Before installation, make sure that the voltage and frequency listed on the data plate correspond with the household electrical supply. This data must correspond to prevent injury and machine damage. Consult a qualified electrician if in doubt. Be certain your appliance is properly installed and grounded by a qualified technician.
Do not lean, sit, or place heavy items on the open oven door. Only use the Miele roast probe supplied with the oven. Contact Miele if you need to purchase a new probe. To prevent damage, remove the roast probe from the oven when it is not being used.
IMPORTANT SAFETY INSTRUCTIONS General notes Do not use a steam cleaner to clean the oven. Steam could penetrate electrical components and cause a short circuit. Children should not be left alone or unattended in an area where an oven is in use.
Guide to the oven a Control panel b SELF CLEAN door lock c Door contact switch * d Upper heating element e Rotisserie motors f Convection fan g Roast probe socket h Light i Non-tip, six level runners j Data plate k Oven door * This switch shuts off the heating element and convection fan when...
a Touch controls to select or set a function. b Keypad to enter times or temperatures. c "On" touch control to turn the oven on. d "Off" touch control to turn the oven off. Guide to the display e Display shows the time or the functions.
Oven accessories Wire rack The racks are to be slid into the runners on either side of the oven. They have non-tip safety notches which prevent them from being pulled out completely while the oven is in use. When inserting a rack, always check that the safety notches are at the rear of the oven.
Oven accessories Roast probe The roast probe reliably monitors the core temperature of meat and poultry during a roasting function. The long pointed end of the probe is inserted into the thickest portion of the meat while the short end of the probe is inserted into the roast probe socket.
Locking the oven System lock The oven is supplied with this setting deactivated as standard. To use it you first have to activate it. The system lock can be activated to prevent children from operating the oven or to conserve standby power when the oven will not be used for some time (e.g.
This oven uses soft key technology and an LCD display to assist in the selection of functions. To select a function, touch the control next to the desired function. The arrow next to each displayed function points to its corresponding control. ^ Touch the "On"...
SETTINGS The default oven settings can be changed in the function "SETTINGS J". In this function you can customize the oven to suit your preferences. Settings may be adjusted by touching the appropriate touch control. Available settings: SETTINGS ( LANGUAGE J... ( CLOCK...
Language J ^ Select the touch control next to the desired language and confirm by touching "OK". The J symbol indicates the "Language" setting. If you accidentally select an unfamiliar language, simply look for the J symbol. Touch the control next to the flag symbol and select your language of choice.
SETTINGS Temperatures The default temperature of each function can be adjusted within the range shown below. If a temperature out of the range is selected, the oven will revert to the default temperature. ^ Touch the control of the function whose default temperature you wish to alter.
Oven Light The "on" duration of the oven light can be altered. ^ Touch the control of the light setting you wish to choose. – "Off after 1 minute" The light goes off after the first minute of a function. –...
SETTINGS Tone Options Unique tones may be set for each of the two timers to differentiate the timers from an oven function tone. "Timer 1" and "Timer 2" The tone of Timer 1 and Timer 2 can be set to one of five tone options. ^ Select "Timer 1 Tone"...
"Tone Short / Long" The duration of the timer and oven tones can be modified. – "Tone short" will beep in quick succession when an oven signal or the oven timer sounds. – "Tone long", a continuous tone will sound when an oven signal or the oven timer sounds.
SETTINGS Reset The factory settings of the oven can be restored through the "RESET" function. – Temperatures – Settings – Favorites Reset Temperatures If the request is confirmed with "Yes", all changed temperatures will be restored to the factory default. Reset Settings If the request is confirmed with "Yes", all changed settings will be restored to the...
Heat the oven New ovens may have a slight odor during the first few uses. To eliminate the odor quickly, the oven should be operated at a high temperature for 2 hours. Before heating the oven for the first time remove (if present) –...
Before using the oven ^ Set the temperature to 500 °F (260 °C) using the keypad. ^ Set the timer to run the oven for 2 hours by touching the "Delay Start" control. ^ Select "Duration". Set the duration by entering "2", "0", "0"...
Selecting a function ^ Touch the "On" control to activate the display. ^ Touch the control next to the function you wish to select. For example, touch the control next to the word "BAKE" to select this function. The "BAKE" function submenu will appear in the display.
Using the oven Preheating For proper cooking results, most recipes call for a preheated oven. After a temperature has been selected, the rising temperature can be viewed in the display. "Preheating" will show in the display until the oven has reached the selected temperature.
Delay Start This function allows you to turn cooking processes automatically off or on and off. Duration To enter the cooking time. After this time has elapsed the oven turns off automatically. The maximum duration time which can be entered is 11 hours 59 minutes.
Using the oven Start time This feature allows you to delay the start of a function, from 1 minute to 23 hours 59 minutes, so that the cooking process begins at a specified time. ^ Touch the "Delay Start" control. ^ Touch the "Start time"...
Using the oven Canceling a process ^ Touch the "Clear" control. ^ Select the option you wish to cancel. The cooking process will be canceled. If the timer was set in addition to a cooking process time, touching "Clear" will show all options which can be canceled.
Setting the timer Setting a timer The timer can be used to time any activity in the kitchen and can be set independently of a cooking function. Two alarms (Timer 1 and 2) can be selected simultaneously. A maximum time of 99 minutes and 59 seconds can be selected.
BAKE Baking tips The roasting pan does not need to be greased or covered with parchment paper. The PerfectClean enamel finish prevents spillovers from baking onto and into the surface. Baked food can be easily removed. Use baking parchment only for dough with a high egg white content, i.e.
BAKE BAKE Default temperature . . . 375 °F (190 °C) The "BAKE" function works by heating food from below. This is similar to the "bake mode" of a conventional oven. Use this function for: – boxed cake mixes, – baked apples, –...
As a general rule, the temperature of a recipe not designed for baking in a convection oven should be lowered by 25 °F (15 °C.) runners...
BAKE SURROUND Default temperature . . . 375 °F (190 °C) The "SURROUND" function is a premi- um conventional baking mode. The oven heats with both the upper and lower heating elements without the convection fan. Use this function for: –...
BAKE INTENSIVE Default temperature . . . 325 °F (160 °C) The "INTENSIVE" function generates heat from the lower heating element. The oven’s fan gently circulates the heated air to create a brick oven (convection) environment. Use this function for: –...
AUTO ROAST Default temperature . . . 325 °F (160 °C) This premium convection function heats the oven to a high temperature to sear the meat, retaining moisture and tenderness. "Searing" appears in the display. Once the meat is seared, the function returns to the selected temperature and "Searing"...
ROAST CONVECTION ROAST Default temperature . . . 325 °F (160 °C) This function uses the convection fan to actively circulate heated air throughout the oven. This function does not spike the oven temperature for searing. Use this function for: –...
ROAST SURROUND ROAST Default temperature . . . 400 °F (200 °C) "SURROUND ROAST" is a conventional roasting program for traditional recipes. Use this function for: – pot roast, – brisket, – stew. The recommended position is the 2 runner from the bottom.
ROAST Roasting tips – The larger the cut of meat to be roasted, the lower the temperature should be. The roasting process will take a little longer, but the meat will be cooked evenly and the outside will become crisp. –...
Using the roast probe The roast probe reliably monitors the roasting process. The tip of the probe continuously measures the core temperature of the meat or poultry. When the selected core temperature is reached, the oven automatically shuts off. The roast probe can be used with the following functions: –...
ROAST When roasting poultry, the best place to insert the probe is in the thickest part of the bird between the thigh and body. ^ Insert the short end of the roast probe into the socket on the right side of the oven so it clicks into place.
^ Enter the desired start time of the roasting process using the keypad. At the end of cooking, when the selected core temperature has been reached, a tone will sound. The tone can be canceled by touching "Clear". Please note: When finished, cover the meat with aluminum foil and allow to stand for 10 minutes.
MASTER CHEF The "MASTER CHEF" function contains an easy to use list of preset functions of commonly cooked foods such as pizza, chicken and french fries. ^ Touch the "MASTER CHEF" control to view the list of preset functions. ^ Touch the control of the function you wish to select.
Tips for use – To end an automatic program prematurely, turn the oven off. – If the food is not cooked to your desire after an automatic program has elapsed, set the oven to Convection Bake 320 °F (160 °C) and cook or brown it for a few more minutes.
BROIL BROIL No default temperature Only the inner part of the upper heating element is used for a smaller area of intense heat from above. This function is excellent for broiling or searing small quantities. Use this function for: – chops, ribs, –...
BROIL MAXI BROIL No default temperature The entire upper heating element is used for intense heating from above. This function gives excellent browning and searing results. Use this function for: – chops, ribs, – large quantities of meat, – browning large dishes. The recommended position is the 4 runner from the bottom.
BROIL CONVECTION BROIL No default temperature Hot air from the upper heating element is distributed over the food by the fan. This enables a lower temperature than conventional broiling to be used. Use this function for: – thick pieces of meat, –...
BROIL ROTISSERIE No default temperature The "ROTISSERIE" function broils meat or poultry while turning it on a spit for even cooking results. Use this function for: – poultry, whole birds, – tied roasts, e.g. pork loin, beef tenderloin, etc., – kebabs. The roast probe cannot be used at the same time as the rotisserie.
^ Secure meat or poultry on the skewers. (Poultry legs should be tied together to prevent them from catching on the heating element or burning.) ^ Assemble the rotisserie as shown. ^ Put the rotisserie in the oven, using the lowest level runner. ^ Insert the spits into the grill motors at the back of the oven.
BROIL Broiling tips – To ensure even cooking, it is best to broil foods of a similar thickness at the same time. Most items should be turned halfway through broiling. – To determine how far through a thick piece of meat has been cooked, press down on its surface with a spoon.
If you often cook a recipe with the same settings (function, time, temperature) you can save them as a "favorite" for easy recall. To save a favorite: ^ Enter the function, temperature and cooking times of the recipe. The oven will begin heating. ^ Touch the "Add to favorites"...
SABBATH SABBATH Default temperature . . . 375 °F (190 °C) For religious observance, the oven can be set to run for the duration of the Sabbath. There will be no visual change to the control panel and the clock will not be displayed. In this function, only "BAKE"...
DEHYDRATE DEHYDRATE Default temperature ..175 °F (80 °C) This function is for dehydrating fruits, vegetables and herbs. A consistent low temperature and the fan maintain the ideal conditions for the long dehydration process. For best results, blot food with a paper towel before dehydrating.
PROOF PROOF Default temperature ..125 °F (50 °C) The warm environment created in the proof function will allow you to effectively proof dough. This function maintains a low temperature perfect for yeast to rise. Place the dough in a large bowl on the oven rack positioned at the lowest runner level.
DEFROST Default temperature ..75 °F (25 °C) This function allows you to defrost food at a constant temperature. Defrosting times depend on the type and weight of the food, and at what temperature it was deep-frozen. Defrosting tips –...
Cleaning Front of appliance It is best to clean spills from the front of the appliance immediately. Spills that remain longer may cause the surface to become discolored or changed. Clean the front of the appliance with a clean sponge or cloth, liquid dish soap and warm water, or a clean, damp micro fiber cloth.
PerfectClean The revolutionary PerfectClean enamel is a smooth, nonstick surface that cleans easily with a sponge. The following have been treated with "PerfectClean": – roasting pan, – wire rack. ^ Do not clean items with PerfectClean in a dishwasher. Dishwasher detergents may damage the enamel.
Cleaning Cleaning the oven cavity by hand Danger of burns! Allow the oven to cool before cleaning. To make cleaning easier – remove the oven door, – remove the runners, – lower the upper heating element. ^ Clean the oven surfaces with a solution of hot water, liquid dish soap and a sponge or soft nylon brush.
Removing the oven door Please note: The oven door is quite heavy. It should be gripped firmly at the sides when being removed or refitted. ^ Open the door fully. ^ Flip up the locking clamps on each door hinge. ^ Slowly shut the door until the protruding clamps stop the movement.
Cleaning Refitting the oven door ^ Insert the door onto the hinges and open the door completely. ^ Flip the locking clamps down. Be sure that the locking clamps are flipped down when the door is reinstalled. Otherwise, on closing the door, the hinges could work loose from the guide holes and cause damage.
Lowering the upper heating element ^ First remove the runners. ^ Loosen the wing nut. ^ Gently lower the upper heating element. Do not use force to lower it, as this could cause damage. ^ Reassemble in the reverse order, ensuring all parts are correctly in place.
Self Cleaning SELF CLEAN function In the self cleaning function, the oven is heated to very high temperatures burning off any residue on the oven interior. The duration of the "SELF CLEAN" function will depend on the amount of soiling in the oven. After the cleaning process, any burnt off debris (e.g.
A film may build up on the oven door. This can be removed with a shielded blade scraper or a non-abrasive sponge and a mild solution of warm water and dish soap. The "SELF CLEAN" function will stop, – if the oven interior is extremely soiled.
Changing the light bulb To reduce the risk of electric shock, disconnect this appliance from the power supply by shutting off the power main or tripping the circuit breaker. Changing the light bulb ^ Remove the runners. ^ Spread a dishtowel on the oven floor to protect the enamel, in case the light cover falls.
^ Replace the halogen bulb. Only use the following light bulb: 12 V, 10 W, 572 °F (300 °C) heat resistant, socket G4, type 64418 made by Osram. Do not touch the new light bulb with your fingers; touching the bulb will reduce its life.
Frequently asked questions What if the oven does not heat? Possible fault The system lock is activated. The circuit breaker has tripped. The delay start has been set. The door is not fully closed. Why is there no noise when the oven door is opened during operation? This is normal.
Miele’s Service department, Extended Service Contracts offered by other providers for Miele products will not be recognized by Miele. Our goal here is to prevent unauthorized (and untrained) service personnel from working on your Miele products, possibly doing further damage to them, you and/or your home.
Optional accessories The following accessories are available for purchase from your Local Miele Dealer or from Miele. Gourmet Pizza form This circular form is suitable for cooking fresh or frozen pizzas, flat cakes, tarts, and baked desserts. Gourmet Baking stone...
Optional accessories Anti-splash insert The anti-splash insert may be placed in the roasting pan to reduce splattering of drippings from meat or poultry. The anti-splash insert is coated with PerfectClean enamel and can be easily cleaned with a sponge and dish soap.
Caring for the environment Disposal of the packing materials The cardboard box and packing materials protect the appliance during shipping. They have been designed to be biodegradable and recyclable. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children.
CAUTION: Before servicing, disconnect the power supply by either removing the fuse, shutting off the power main or manually "tripping" the circuit breaker. Installation work and repairs should only be performed by a qualified technician in accordance with all applicable codes and standards. Repairs and service by unqualified persons could be dangerous and the manufacturer will not be held...
Appliance and Cut-out Dimensions a Vent cut-out (min. 24" / 150 cm ) possible at rear or platform of cabinet b Cut-out for power cord (min. 1" / 3 cm c Power cord For the most current specifications see the Miele web site.
The oven must be installed into cabinetry and be supported from underneath. IMPORTANT INFORMATION Certain cabinet materials and finishes are very sensitive to high temperatures. To eliminate the risk of damage to surrounding cabinets, a 24 square inch (2"x12") [150 cm minimum opening must exist in the cabinet to allow air to flow into and around the appliance.
Installing the oven ^ Slowly shut the door until the protruding clamps stop the movement. Pull the door upward. ^ Connect the oven to the electrical supply. ^ Slide the oven into the cabinet and align. ^ Reinstall the door. ^ Open the oven door and locate the two mounting screw holes in the oven frame.
Set the time "Enter Time: hh:mm" will appear in the display once the oven is connected to electricity. ^ Set the current time using the keypad. ^ Save the time by touching the "OK" control. Installing the oven...
Alteration rights reserved / 4508 M.-Nr. 07 338 230 / 00 (H 4882 BP) For the most updated manual see the Miele web site.