Advertisement

quadrone
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Vision AW-QDR-POV and is the answer not in the manual?

Questions and answers

Summary of Contents for Quadrone Vision AW-QDR-POV

  • Page 1 Instruction Manual...
  • Page 2: Accessories List

    Accessories List Upper Cover Lower Cover Circuit Board Landing Feet of Casing of Casing Carbon Fiber Lithium Battery Propellers Bearing Spindle Red and Blue Black and White Green Light Red Light Line Motor Reverse Motor Tail Light Bearing Panel...
  • Page 3: Standard Accessories

    Standard Accessories 3.7V 730 mAh Charger x1 Li-po Battery x1 Propellers x4 Packing List Part Name Quantity Instruction Manual Quadcopter Charger Li-po Battery Propellers Remote Control Upgradeable Accessories (Optional) Water Shooter 5.8G FPV Camera WIFI FPV WIFI FPV Bubble Shooter 5.8G FPV...
  • Page 4: Notice

    Notice • All instructions, warranties and other collateral documents are subject to change at the sole discretion of our company. Warnings • Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property or cause serious injury.
  • Page 5: Table Of Contents

    Introduction • Thank you for choosing Quadrone! This is a four-axis aircraft that can fly outdoors, in order to make it easier to control the aircraft. Please carefully read this manual before operating your Quadrone. Please keep this manual for future reference.
  • Page 6: Battery Usage And Warnings

    The battery charger included with your Quadrone has been designed to safely charge your Li-po battery. CAUTION: All instructions and warnings must be followed exactly. Mishandling of Li-po batteries can result in fire, personal injury, and/or property damage.
  • Page 7: Charging The Battery

    Charging the Battery Only use charger provided. Attach Li-po battery to charging line of charger. Plug charger into power outlet. LED light should light up to indicate it is charging. Charging cable 3.7V 730mAh First Flight Preparation 1. Make sure the battery is fully charged. 2.
  • Page 8: Syncing The Quad And Remote

    Syncing the Quad and the Remote Step 1 Place the quadcopter on a flat surface and place the Li-po battery into the quadcopter. Plug the battery into the quad and the LED lights will begin to flash. Step 2 Turn the remote controller on. Push the throttle stick to its lowest position.
  • Page 9: Remote Diagram

    Remote Diagram Power Switch LED Light Antenna 360 Degree Flips Camera Direction Control Stick Ascending/Descending Forwards and Backwards Trim Speed Trim Directional Trim Sideways Trim 40% Flying Speed X-Axis Calibration 100% Flying Speed 60% Flying Speed Y-Axis Calibration One Key Return Take Photo 80% Flying Speed (Hold 2 Seconds...
  • Page 10: 360 Degree Flips

    Flight Controls If you are not familiar with the controls of your Quadrone, please take a few minutes to review them before take off. Ascending/Descending Throttle Up Ascend Throttle Down Descend Turning Throttle Left Nose Turns Left Throttle Right Nose Turns Right...
  • Page 11: One Key Return

    One Key Return Hold the One Key Return button for 2 seconds. The quadcopter will beep and the tail light will flash. The quadcopter will now return to the remote controller. Headless Mode Hold the Headless Mode button for 2 seconds and you will hear the controller begin to beep, indicating it has entered Headless Mode.
  • Page 12: Circuit Board Schematic

    Quadcopter still wanders forward after 1. Surface during power up was not flat. Quadcopter still wanders forward after trim adjustment during hover. 2. Trim was too long or too short. trim adjustment during hover. 1. Motor fell out. Cannot fly the quadcopter fully. Cannot fly the quadcopter fully.
  • Page 13 Circuit Board...
  • Page 14: Parts List

    Parts List Part Quantity Protective Guard Propeller Upper Body Receiver Board Bearing Battery Cover Battery Electric Machinery Light Lampshade Lower Body Carbon Fiber Spindle Tail Light Plate Cone Tail Light Lamp Shade Landing Feet Quadcopter Parameters Length 14.75” Height 2.25” Propeller Length 5.25mm Battery Specification...

Table of Contents