Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Nine Eagles SOLO PRO 130
Summary of Contents for Nine Eagles SOLO PRO 130
-
Page 1: Operating Instructions
Operating Instructions SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522... - Page 2 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522...
- Page 3 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Explanation of specialist terms: Contents Page Explanation of specialist terms / Contents Climb and descent ("Throttle/pitch"): This controls Safety Notes 4, 5 the model's climb and descent. Set contents / Specification Yaw: The model's movement around the vertical axis;...
- Page 4 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Do not stand close to the hazard area around rotating parts when Be sure to read these Safety Notes before you assemble your mo- del. Always keep to the procedures and settings recommended in an electric motor is connected to the flight battery.
- Page 5 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Do not carry out modifications to the radio control system components Insurance apart from those described in the instructions. Ground-based models are usually covered by standard personal third- party insurance policies.
- Page 6 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Dear customer, Congratulations on choosing a factory-assem- bled model helicopter from our range. Many thanks for placing your trust in us. The model can be completed and prepared for flight very quickly.
- Page 7 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Transmitter description* (Mode 1) - The mode select switch** is located on the back of the transmitter (*Complete operating instructions for the J6 transmitter can be found in the Download area at www.robbe.com)
- Page 8 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Transmitter description* (Mode 2) - The mode select switch** is located on the back of the transmitter (*Complete operating instructions for the J6 transmitter can be found in the Download area at www.robbe.com)
- Page 9 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Transmitter LCD screen Collective pitch and throttle adjustment (default settings) Normal flight Mode display Transmitter voltage display Throttle Collective pitch Collective Display pitch Gyro Channel reverse channel display...
- Page 10 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Receiver outputs Flybarless check before the first flight Climb: Descend: Roll servo Pitch-axis servo Yaw left: Yaw right: Rotational speed Collective pitch servo Tail rotor motor Pitch forward:...
- Page 11 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Charging the flight battery Re-binding the transmitter Connect the battery charger to the This procedure is only necessary mains PSU, and plug the PSU into a if individual components are re- mains socket.
- Page 12 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Safety Notes regarding LiPo batteries: • Do not place the battery in water or any other liquid. • Never heat or incinerate the pack, or place it in a microwave oven. • Avoid short-circuits, and never charge the battery with reversed polarity • Do not subject the battery to pressure or shock loads, and never distort or throw the pack • Never solder directly to the battery • Do not modify or open the battery • Batteries must only be charged with a suitable charger; never connect the battery directly to a mains power supply. • Never charge or discharge a battery in bright sunlight, or close to a heater or open fire. • Do not use the battery in areas subject to high levels of static electricity. • Any of these errors can result in damage to the battery, explosion or fire. • Keep the battery out of the reach of children • If electrolyte should escape, do not expose it to fire, as the material is highly inflammable and may ignite.
-
Page 13: Flight Preparation
Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Flight preparation Open the battery compartment and insert the dry or rechargeable cells. Close the battery compartment. Move all the switches to the forward position, then switch the transmitter on (Fig. 1). If switch "A" or "B" are at the "ON" position, the screen will flash and you will hear a "beep"... - Page 14 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Flight preparation Check the correct position of the swashplate before the first flight. The swashplate must sit exactly horizontal when viewed from the side and front of the model. Position the model on a totally flat surface. Now move the throttle stick to the lowest throttle position, and switch the transmitter on.
- Page 15 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Important Notes The first few flights Take-off: use the 3D switch for aerobatics only. To take off, slow- Ideally the first flight should take place in a large indoor space ly and steadily increase rotor speed until the model is hovering devoid of obstructions.
- Page 16 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Trim settings Mode 1 Trim settings Mode 2 Throttle trim: Throttle trim: If the rotor starts to move without the If the rotor starts to move without the...
- Page 17 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Controlling the model in Mode 1 Controlling the model in Mode 2 Lift off: Landing: Lift off: Landing: Yaw left: Yaw right: Yaw left: Yaw right: Pitch forward:...
- Page 18 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 Replacement Parts List - SOLO PRO 130 EC145 RTF No. Order No. Description 01 NE252201 Rotor head 02 NE252208 Blade pivot shaft 03 NE252008 Ballrace set 1 04 NE252020...
- Page 19 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522...
- Page 20 Operating Instructions - SOLO PRO 130 EC145 RTF 2.4 GHz No. NE2522 robbe Modellsport GmbH & Co. KG hereby declares that this device conforms to the fundamental requirements and other relevant regulations of the corresponding EC Directive. You can read the original Conformity Declaration on the Internet at www.robbe.com: click on the "Confor- mity Declaration"...
Need help?
Do you have a question about the SOLO PRO 130 and is the answer not in the manual?
Questions and answers