Hitachi CR 10DL Handling Instructions Manual page 44

English
Table 3: Bl-METAL blades
Blade
Uses
No.
No. 101 For cutting steel and stainless pipes
less than 60 mm in outer diameter
No. 103 For cutting steel and stainless pipes
less than 60 mm in outer diameter
No. 107 For cutting steel and stainless pipes
less than 60 mm in outer diameter
No. 109 For cutting steel and stainless pipes
less than 60 mm in outer diameter
No. 132 For cutting and roughing lumber
NOTE
Nos. 101 – No. 132 Bl-METAL blades are sold
separately as optional accessories.
3. Selection of blades for other materials
Table 4
Material Material
to be cut quality
Iron plate Mild steel
plate
Nonferrous Aluminium,
metal Copper and
Brass
Systhetic Phenol resin,
resin Melamine
resin, etc.
Vinyl chloride,
Acrylic resin,
etc.
MAINTENANCE AND INSPECTION
CAUTION
Be sure to turned off the switch and remove the
battery before maintenance and inspection.
1. Inspecting the blade
Continued use of a dull or damaged blade will
result in reduced cutting efficiency and may cause
overloading of the motor. Replace the blade with
a new one as soon as excessive abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure
that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure
to do so could result in serious hazard.
3. Maintenance of the motor
The motor unit winding is the very "heart" of the
power tool. Exercise due care to ensure the winding
does not become damaged and/or wet with oil or
water.
43
Thickness
(mm)
2.5 – 6
2.5 – 6
Below 3.5
2.5 – 6
100
Thickness
Blade No.
(mm)
2.5 – 10 No. 2, 101,
103, 109
Below 3.5 No. 3, 107
5 – 20 No. 2, 101,
103, 109,
132
Below 5 No. 3, 107
10 – 50 No. 2, 4,
101, 103, 132
5 – 30 No. 3, 5, 8,
107, 109
10 – 60 No. 2, 4,
101, 103, 132
5 – 30 No. 3, 5, 8,
107, 109
4. Cleaning of the outside
When the Cordless Reciprocating Saw is stained,
wipe with a soft dry cloth or a cloth moistened with
soapy water. Do not use chloric solvents, gasoline
or paint thinner, as they melt plastics.
5. Storage
Store the Cordless Reciprocating Saw in a place in
which the temperature is less than 40°C, and out
of reach of children.
6. Service parts list
CAUTION
Repair, modification and inspection of Hitachi Power
Tools must be carried out by an Hitachi Authorized
Service Center.
This Parts List will be helpful if presented with the
tool to the Hitachi Authorized Service Center when
requesting repair or other maintenance.
In the operation and maintenance of power tools,
the safety regulations and standards prescribed in
each country must be observed.
MODIFICATIONS
Hitachi Power Tools are constantly being improved
and modified to incorporate the latest technological
advancements.
Accordingly, some parts may be changed without
prior notice.
GUARANTEE
We guarantee Hitachi Power Tools in accordance with
statutory/country specific regulation. This guarantee
does not cover defects or damage due to misuse, abuse,
or normal wear and tear. In case of complaint, please
send the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a Hitachi Authorized Service Center.
NOTE
Due to HITACHI's continuing program of research and
development, the specifications herein are subject to
change without prior notice.
Information concerning airborne noise and vibration
The measured values were determined according to
EN60745 and declared in accordance with ISO 4871.
Measured A-weighted sound power level: 95 dB (A).
Measured A-weighted sound pressure level: 83 dB (A).
Uncertainty KpA: 3 dB (A).
Wear hearing protection.
Vibration total values (triax vector sum) determined
according to EN60745.
Vibration emission value
Uncertainty K = 2.4 m/s
a
h = 13.0 m/s
2
2