Asus Motherboard P5MT-M Product Manual page 47

4 . 4 . 4 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 ,
4 . 4 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 ,
S A T A 4 ) S A T A 4 ) S A T A 4 ) S A T A 4 ) S A T A 4 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 5, or RAID 10 configuration with the onboard Intel
ICH7R RAID controller.
These connectors are set to S t a n d a r d I D E
S S S S S t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard disk t a n d a r d I D E
drives to these connectors. If you intend to create a Serial ATA RAID set
using these connectors, set the C o n f i g u r e S A T A
to [RAID]. See section "4.3.5 IDE Configuration" for details.
®
LAN2
P5MT-M SATA connectors
When using the connectors in S S S S S t a n d a r d I D E
primary (boot) hard disk drive to the SATA1 or SATA2 connector. Refer
to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r
C o n n e c t o r C o n n e c t o r C o n n e c t o r
S A T A 1 , S A T A 2 S A T A 1 , S A T A 2
S A T A 1 , S A T A 2 S A T A 1 , S A T A 2 S A T A 1 , S A T A 2
S A T A 3 , S A T A 4 S A T A 3 , S A T A 4 S A T A 3 , S A T A 4
S A T A 3 , S A T A 4 S A T A 3 , S A T A 4
A S U S P 5 M T - M A S U S P 5 M T - M A S U S P 5 M T - M
A S U S P 5 M T - M A S U S P 5 M T - M
S t a n d a r d I D E mode by default. In S t a n d a r d I D E S t a n d a r d I D E
S t a n d a r d I D E
C o n f i g u r e S A T A a a a a a s s s s s item in the BIOS C o n f i g u r e S A T A C o n f i g u r e S A T A
C o n f i g u r e S A T A
SATA1
SATA2
SATA3
SATA4
t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, connect the t a n d a r d I D E
S e t t i n g S e t t i n g U s e U s e
S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e
M a s t e r M a s t e r B o o t d i s k B o o t d i s k
M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k
S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k
S l a v e S l a v e D a t a d i s k D a t a d i s k
®
2 - 2 7 2 - 2 7 2 - 2 7
2 - 2 7 2 - 2 7