Vivitek D-Point 2 User Manual
  1. Manuals
  2. Brands
  3. Vivitek Manuals
  4. Interactive whiteboard
  5. D-Point 2
  6. User manual
Vivitek D-Point 2 User Manual

Vivitek D-Point 2 User Manual

Hide thumbs

Advertisement

Table of Contents

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the D-Point 2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Vivitek D-Point 2

Summary of Contents for Vivitek D-Point 2

  • Page 2: Table Of Contents

    Contents Accessories of D-Point 2 ....................2 Connecting Projector to PC .................... 4 Pen Action ........................4 Driver Installation ......................5 Configuration Setting ..................... 8 D-Point 2 Pull-up Menu ....................12 DT01 Multi-touch Interactive Module (Optional) ............13 Specifications ....................... 27 Trouble shooting ......................
  • Page 3  Drop the IR Pen. IR Pen tip is designed precisely.  Operating Keystone, performance for the Interactive function may decline.  Set lamp mode to “Eco” may cause “Auto Calibration” abnormal operation of the D-Point 2. - 1 -...

  • Page 4: Accessories Of D-Point 2

    1 Accessories of D-Point 2 D-Point 2 is a built in Interactive Whiteboard on the Projector. To use the D-Point 2 correctly, please find necessary accessories and follow the instructions in this manual. In the projector box, you will find the following accessories.
  • Page 5 1.1 Installing CHANGEABLE TIPS Clenched and forced to pull out the tip. Installing a new Pen Tip until you feel it click with Pen. Complete the replacement tip. - 3 -...

  • Page 6: Connecting Projector To Pc

    1. In the accessories, a 5m USB cable is provided. If more than 5 meter USB cable length is required, then use repeater cable to extend the USB cable length. 2. Do not connect the projector with the PC when D-Point 2 driver install. 3 Pen Action IR Pen provides four actions, Click, Double Click, Right Button Click and Drag.

  • Page 7: Driver Installation

    Display (1920x1200), Display color in16-bit color or greater. Insert the D-Point 2 CD into your CD/DVD-ROM driver. The Installation assistant will run automatically. Follow the instructions in the installation assistant. If the assistant does not run automatically, double click the “ setup.exe” under CD/DVD-ROM directory and the Installation assistant will run.
  • Page 8 4.3 The installation dialog box will appear. Click next. During installation, it is recommended to close other applications. 4.4 Click Install, installation begins. 4.5 Installation ends, then dialog box will indicate finish. Click “Finish”. - 6 -...
  • Page 9  D-Point 2 icon will be created on the desktop.  Installation folder will be created on C: directory. Upon starting D-Point 2, the configuration window will appear on the desktop to assist in setting up the D-Point 2 configuration...

  • Page 10: Configuration Setting

    5 Configuration Setting 5.1 D-Point 2 Configuration To use the D-Point 2, the proper setting of the D-Point 2 configuration is needed. The Configuration setting window will help you set-up the D-Point 2 correctly. Model Selection: Select “Ultra Short Throw Model”. If the incorrect model is selected, accuracy will drop.
  • Page 11 5.2 D-Point 2 Alignment : Alignment View D-Point 2 Alignment : Interactive Projector Model does not need alignment process. When necessary only use “Alignment View” function. Alignment View : Upon clicking “Alignment View”. - 9 -...
  • Page 12 5.3 D-Point 2 Calibration D-Point 2 provides two kinds of calibration methods, Auto Calibration and Manual Calibration. Auto Calibration : click , the calibration process will run automatically. Manual Calibration : Click , and the calibration window will be projected to the screen.
  • Page 13 Make sure your touch center of the cursor marked; otherwise, it may not be positioned correctly. Depending on circumstances, Auto Calibration may fail or accuracy may not be adequate. In this case, please calibrate manually. - 11 -...

  • Page 14: D-Point 2 Pull-Up Menu

    After you run the D-Point 2 by double clicking D-Point 2 icon on the desktop, D-Point 2 icon will be shown in the system tray. Right button click D-Point 2 icon in windows menu bar, then pull up menu appears. Label Description Only when you want to change mounting position of Projector, to change language, click this menu and follow the step “5.

  • Page 15: Dt01 Multi-Touch Interactive Module (Optional)

    7 DT01 Multi-touch Interactive Module (Optional) 7.1 Accessories of DT01 DT01 Multi-touch Interactive Module is a touch transmitter for the Vivitek interactive projector. To use the touch module, please find the standard accessories below and follow this manual. DT01 Multi-touch...
  • Page 16 7.1.1 Installing CHANGEABLE TIPS Note: For better touch performance, keep the pen tip clean Counterclockwise direction to unlock pen tip. Installing a new Pen Tip with Clockwise direction to lock pen tip. Complete the replacement tip. - 14 -...
  • Page 17 7.1.2 About DT01 Multi-touch Interactive Module Front View Rear Vieaw Right View Dimensions 39mm 170mm - 15 -...
  • Page 18 7.2 Screen Board Requirement 7.2.1 Shape of Screen board vs Laser curtain Convex screen board : Center area, laser curtain height is proper but the edge area laser curtain height becomes too high. Screen Board Laser curtain Laser Curtain Laser Curtain Laser Curtain height is good is too High...
  • Page 19 7.3 DT01 System Configuration 7.3.1 Beamed Screen Position Gap between sides/bottom of beamed screen and frame edge should be larger than 50mm. Center line of touch area 50-100mm DT01 touch module Frame Surface Touch area 50mm 50mm 50mm Item Specification Horizontal Position Center Line of beamed screen.
  • Page 20 7.3.2 Mounting Method of DT01 Multi-touch Interactive Module 2 kinds of method : Install the adhesive tape on the rear side of the DT01 Multi-touch Interactive Module. Following the instructions above to position the DT01 on the screen. Note: (thickness: 1mm) is recommended. Turn over the front cover.
  • Page 21 7.3.3 Connecting DT01 Connecting DT01 Use the USB cable to connect the DT01 for power supply. There are three ways to connect the DT01. Connect DT01 to Projector (Recommended) Note: USB type-A power is available for selected projector model. Connect DT01 to Computer Caution: USB power may be unstable under the following conditions: ...
  • Page 22 7.4 Laser curtain characteristics 7.4.1 Fan angle of laser curtain Laser curtain covers 180 degree and form a laser curtain. Laser curtain is perfect plane with 2mm thickness. 7.4.2 Laser curtain position on the screen board Laser curtain shall not be contact with screen and it’s height should be low enough.
  • Page 23 7.4.3 Laser Curtain Alignment Principle Rolling/Pitch/Level control of Laser Curtain Knob 1 : Pitching control / Knob2, Knob3 : Rolling control Knob1 Knob2 Knob3 Pitching control Rotate knob 1 in clock wise, then laser curtain goes up like figure below. And if rotate knob 1 in anti-clock wise, then laser curtain goes down Rolling control Rotating knob 2 in anti-clock wise, then left side of laser curtain goes up.
  • Page 24 7.5 Laser curtain alignment 7.5.1 Alignment view of laser curtain Enter “Alignment View” function under “Pen mode”. (*) *: Before setting DT01 Multi-touch Interactive Module, please finish “Pen mode” auto or manual calibration. - 22 -...
  • Page 25 Alignment view Connect the USB cable for DT01 - 23 -...
  • Page 26 7.5.2 Using Alignment Mask Shape of Alignment Mark Mounting Position of Alignment Mark : - 24 -...
  • Page 27 7.5.3 Laser curtain alignment process First rotate slowly #1 knob then you can see the reflection line like below picture Then,rotating #2/#3 knob accordingly to make reflection line horizontal and near the laser module. Rotating #1 knob slowly and until see one white reflector point of alignment mark - 25 -...
  • Page 28 Finally rotating #1 knob anti-clockwise and stop once seeing two white reflector points of alignment mark Switching “ Finger Touch mode” from PC / NB device and start to use finger touch function. - 26 -...

  • Page 29: Specifications

    8 Specifications Touch module DT01 Model Name Operating Voltage 4.7~5.2V Power Consumption Max 180mA USB Type (Power) Mini USB B type Power Source Power via USB connector or 5V adaptor Wavelength 850nm ± 10nm Fan Angle Max : 180° (1 laser beam) Rolling Control Range Max 4°...

  • Page 30: Trouble Shooting

    9 Trouble shooting 9.1 Cannot operate as a mouse and draw by connecting to a computer  Is Configuration set correctly? Make the following settings to link with the computer's functions. - Set projector type – Short throw or ultra short throw from the configuration menu. - Set projector mounting type –Normal or Ceiling mount from the configuration menu.

This manual is also suitable for:

D-point 3

Table of Contents