Remote Control Unit - Denon DVD-3910 Operating Instructions Manual

ENGLISH
6

REMOTE CONTROL UNIT

The DVD-3910 can be controlled from a distance using the included remote control unit (RC-972).
2
(1) Inserting Batteries
q Remove the remote control unit's rear cover.
w Place two R6P/AA batteries in the battery
compartment in the direction indicated by the
marks.
e Close the rear cover.
(2) Using the Remote Control Unit
Approx. 7 meters
30°
30°
14
Cautions On Batteries
• Use R6P/AA batteries in this remote control unit.
• Replace the batteries with new ones approximately
once a year, though this depends on the frequency
with which the remote control unit is used.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less than a year has passed.
• The included battery is only for verifying operation.
Replace it with a new battery as soon as possible.
• When inserting the batteries, be careful to do
so in the proper direction, following the < and
> marks in the remote control unit's battery
compartment.
• To prevent damage or battery fluid leakage:
• Do not use a new battery with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When operating the remote control unit,
point it at the remote control sensor as
shown on the diagram.
• The remote control unit can be used from a
direct distance of approximately 7 meters.
This distance will be shorter, however, if
there are obstacles in the way or if the
remote control unit is not pointed directly
at the remote control sensor.
• The remote control unit can be operated at
a horizontal angle of up to 30° with respect
to the remote control sensor.
NOTES:
• It may be difficult to operate the remote
control unit if the remote control sensor is
exposed to direct sunlight or strong
artificial light.
• Do not press buttons on the main unit and
on the remote control unit at the same
time. Doing so will result in malfunction.
(3) Names and Functions of Remote Control Unit Buttons
Button not explained here function in the same way as the corresponding buttons on the main unit.
2
POWER OFF POWER ON
q
HDMI/DVI OPEN/
w
NTSC/PAL
SELECT FORMAT CLOSE
!9
SUPER AUDIO
CD SETUP
PROGRAM
@1
/DIRECT
e
@2
CLEAR
SEARCH MODE CALL
@3
r @5
BACK LIGHT ANGLE SUBTITLE AUDIO
t
TOP MENU DISPLAY
@7
y
u
MENU RETURN
i @8
STOP STILL/PAUSE PLAY
o @9
!0
#0
SKIP SLOW/SEARCH
!1
!2 #1
REPEAT A-B PAGE
!3
!4
RANDOM MARKER ZOOM DIMMER
#3
!5
PICTURE PURE DIRECT
!6 SETUP ADJUST MEMORY SELECT
#4
!7
q
POWER ON/POWER OFF buttons
• Press this to switch the power between on
and standby.
w
HDMI/DVI SELECT/FORMAT buttons
• Use these to select to use HDMI terminal or
DVI terminal, and the format of video signals
(480P/576P,720P,1080i).
e
Number buttons
• Use these to input numbers.
Use the +10 button to input numbers of 10 or
over.
Example: To input 25
r
LIGHT button
• Press this to light the opal color button.
Press again this to put out light.
t
ANGLE button
•
Press this to switch the angle.
y
TOP MENU button
• The top menu stored on the disc is displayed.
u
Cursor buttons/ENTER button
• Use the • and ª cursor buttons to select in
the vertical direction.
Use the and cursor buttons to select in
0 1
the horizontal direction.
Press the ENTER button to select the item
selected with the cursor buttons.
i
MENU button
• The DVD menu stored on the disc is
displayed.
o
STOP button ( )
2
!8 !0
STILL/PAUSE button ( )
3
!1
SKIP buttons
@0
!2
REPEAT button
• Press this to play tracks repeatedly.
!3
A-B repeat button (A-B)
• Use this to repeat sections between two
@4
specific points.
!4
RANDOM button
@6
• Press this to play the tracks on the video or
music CD in random order.
!5
MARKER button
• Press this to mark places you want to see
again.
!6
SETUP button
• Press this to display the default setting
screen.
!7
PICTURE ADJUST button
• Press this to adjust the picture quality to suit
#2 your tastes.
!8
OPEN/CLOSE button
!9
NTSC/PAL button
• Use this to switch the set's video output
format (NTSC/PAL).
@0
SUPER AUDIO CD SETUP button
@1
PROGRAM/DIRECT button
• Press this to switch between the normal play,
programmed play.
@2
CLEAR button
• Press this to clear numbers that you have
input.
@3
CALL button
• Press this to check the program contents.
@4
SEARCH MODE button
•
Press this to change the search mode to search for
groups or titles, tracks or chapters when selecting
sections of discs directly using the number buttons.
@5
AUDIO button
• For DVDs, press this to switch the audio
language. For video CDs, press this to switch
the channel between "STEREO", "MONO
LEFT" and "MONO RIGHT".
@6
SUBTITLE button
• Press this to switch the DVD's subtitle
language.
@7
DISPLAY button
• Press this to display the ON-SCREEN.
@8
RETURN button
• Press this to return to the previous menu
screen.
@9
PLAY button ( )
1