1. Manuals
  2. Brands
  3. Luxor Manuals
  4. Indoor Fireplace
  5. MB-36
  6. Installation and owner's manual

Luxor MB-36 Installation And Owner's Manual

Zero clearance direct vent gas fireplaces
Hide thumbs

Advertisement

Table of Contents

Zero Clearance Direct Vent Gas Fireplaces
Installation and Owner's Manual
PLEASE NOTE: This product has been manufactured using steel and screws. As a
result, there are many sharp edges that can easily cut exposed skin. It is highly
recommended that you wear proper protective gloves while installing the unit, and
during routine cleaning or maintenance..
PLEASE READ INSTRUCTIONS CAREFULLY BEFORE
INSTALLING AND OPERATING THE APPLIANCE
WARNING: If the information in these instructions are not followed exactly, a fire or
explosion may result causing property damage, personal injury, or loss of life.
Installation and service must be performed by a qualified installer, service agency, or the
gas supplier.
This appliance may be installed in a permanent home, and is suitable for bedroom or
sitting room.
FOR YOUR SAFETY
DO NOT store or use gasoline or any other
flammable vapors or liquids within the vicinity of
this or any other appliance.
IN THE EVENT THAT YOU SMELL GAS
-Do not try to light any appliance
-Open windows
-Do not touch electrical switches
-Do not use any phone in your building
-Extinguish any open flame
-Call your gas supplier from a neighbors phone
and follow the gas suppliers instructions.
-If you cannot reach the gas supplier, call the fire
department
Installer: Please leave this manual with the customer
Customer: Please keep instructions for future reference
Model MB-36
Canadian Fire Hearth Mfg, Inc
Ph: (604) 857-5564, (604) 826 7100, Fax: (604) 826 7122,
7057 Beatty Drive British Columbia,
Canada, V2V 6C4
Web: www.firehearth.ca

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MB-36 and is the answer not in the manual?

Questions and answers

Related Manuals for Luxor MB-36

Summary of Contents for Luxor MB-36

  • Page 1 Zero Clearance Direct Vent Gas Fireplaces Model MB-36 Installation and Owner’s Manual PLEASE NOTE: This product has been manufactured using steel and screws. As a result, there are many sharp edges that can easily cut exposed skin. It is highly recommended that you wear proper protective gloves while installing the unit, and during routine cleaning or maintenance..
  • Page 2 Serial Number:___________________________________________________ Welcome! Congratulations on the purchase of your new Luxor Gas Fireplace! We hope you’ve had an easy and enjoyable time choosing from our line of products, and we certainly appreciate your business. Please take some time to read through the following information, and make sure to heed all of the warnings.
  • Page 3 Table of Contents: Page 1: Pre-Start Up Page 2: General Safety Page 3: Specifications Page 4: Framing & Clearances Louvered Page 5: Framing & Clearances Clean Face Page 6: Framing & Clearances for Santa Fe Page 7: Venting Page 8: Venting Continued Page 9: Venting Continued Page 10: Door Fitting Page 11: Electrical...

  • Page 4: Specifications

    Viewing area: 30” 19” Certification The Model MB-36 is listed and certified for the installation in the U.S.A. and Canada under the following standards: ANSI Z21.88/CSA 2.33. The installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 / NFPA 54 in the US, or the Natural Gas and Propane...

  • Page 5: Corner Installation

    Inside framed size for termination: -Luxor horizontal with flex: 10” x 10” inside It is best to frame your -Simpson DuraVent (P/N 984) 10” x 11” fireplace after it is...
  • Page 6 41¼” Inside framed size for termination: -Luxor horizontal with flex: 10” x 10” inside -Simpson DuraVent (P/N 984) 10” x 11” Please note: Wall thimble (P/N 942) may be required for installations in Canada.
  • Page 7 41¼” Inside framed size for termination: -Luxor horizontal with flex: 10” x 10” inside -Simpson DuraVent (P/N 984) 10” x 11” Please note: Wall thimble (P/N 942) may be required for installations in Canada.
  • Page 8 Installation of Clean Face Kit continued 4 self tapping screws in pre-drilled holes. Please note: standoffs must be removed for installation of clean face kit. The CFK then becomes the standoffs. Lip goes at the top as shown. Please note: the custom doors we manufacture for this unit fit inside the opening, so do not bring finishing products beyond the opening.
  • Page 9 Venting Identification WARNING: This gas appliance must not be connected to a chimney flue serving a separate solid-fuel burning appliance. Before unit installation, provisions for adequate combustion and ventilation must be made. Simpson Dura-Vent Flex -Horizontal Termination only SD-0961 30 elbow (vertical) °...
  • Page 10 12’ horizontal Attention: Any venting configuration that completes with a vertical termination requires installation of CFHM Part # MBR Restriction. 12’ horizontal 32’ vertical For horizontal termination, you can use either Simpson DuraVent or Flex with Luxor 32” Termination. Page9...
  • Page 11 Venting Continued QUALIFIED INSTALLERS ONLY When planning an installation it will be necessary to select to proper length of vent pipe for the particular requirements. It is important to note that, when passing Simpson Duravent pipe through a wall thimble (p/n 942) maybe required in Canada. Check local codes. Flex pipe installations require Mill-Pac sealant on exhaust joints.
  • Page 12 Door Fitting WARNING: Do not abuse the appliance’s glass by striking, slamming or similar trauma. Do not use the appliance with the door removed, glass panel cracked or broken. Only use tempered glass approved for use with this appliance. Do not use substitute materials. Replacement of the panel should only be carried out by a licensed qualified service person.
  • Page 13 Electrical Applicable when installed. WARNING Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three prong receptacle. Do not cut or remove the grounding prong from this plug. L1(BK) Fan Motor Resistor Adjustable...

  • Page 14: Gas Supply Installation

    Planning The recommended order of installation is as follows: 1-Familiarize yourself with this manual. 2-Check the minimum install dimensions and vent installation. 3-Check your local install codes. 4-Check you have the parts and components necessary to complete the installation. 5-Check the gas and electrical supplies are ready. 6-Prepare opening (clean chase, level base etc.) 7-Install Venting.
  • Page 15 Optional Fan Kit Each kit contains: -Fan assembly with mounting gasket -Grounded electrical harness -Reostate & thermal switch Double fan kit shown. Caution: The appliance contains many sharp edges. Make sure to wear proper gloves. 1. Shut off any electrical to the unit if applicable. 2.

  • Page 16: Thermostat Installation

    Thermostat Installation Thermostat or wall switch installation The burner control switch is located in the center of the control department opening. For your convenience, the unit can also be operated by a thermostat or a wall switch control. Millivolt thermostats are available from any authorized CFHM dealer.

  • Page 17: Log Installation

    Log Installation Make certain that none of the fire holes or the pilot are blocked while installing the log set. Logs are brittle and easily damaged. Handle with care. Distribute vermiculite evenly over the burner. Spread it near and around the flame holes, but do not block any of them.
  • Page 18 Logs Installation Continued Fiber “ember” mater to be placed sparingly across the front of the log set. Careful not to block any of the flame holes. These installation pictures are with the optional Brick Set installed. If you do not have the 3 piece brick set, the background will be black.

  • Page 19: Parts List

    Parts List Replacement Parts Part No. Description FD-101 #47 Orifice FD-102 #46 Orifice FD-103 SIT Pilot Assembly FD-104 SIT Gas Valve MB-700 Log Set Log set MB-DR2 Glass & Frame MB-701 Black Louvers MB-702 Plated Louvers MB-703 Plated Door MB-704 Black Surround MB-705 Plated Surround...

  • Page 20: Lighting Instructions

    Lighting Instructions For your safety, read the following before lighting. WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage and personal injury or death. A. This appliance has a pilot which must be lighted -If you cannot reach your gas supplier, call the fire by hand.

  • Page 21: Final Checks

    Final Checks Installer: Before leaving the appliance with the 1. Clean the glass regularly as soon as you notice customer, you must check the operation of the the buildup, (white film). If the film is left for a longer appliance. period of time, build up will bake on.

  • Page 22: Trouble Shooting

    Trouble Shooting Please check to make sure the instructions are followed exactly before attempting trouble shooting of the appliance. Warning: Installation, trouble shooting and servicing of gas and electrical devices of the appliance should only be conducted by a qualified installer, service technician or the gas supplier. Caution: Label all wires prior to disconnection when servicing controls.
  • Page 23 -Remove the screws that hold the valve plate assembly -Carefully lift out the assembly Fan Assembly A fan assembly is available for the model MB-36. For details on fan installation and service, see separate documentation supplied with a the fan kit. Venting System The appliance should be inspected before use and at least annually by a professional service person.
  • Page 24 Maintenance Continued More frequent cleaning may be required due to excessive lint from carpet bedding material etc. It is imperative that control compartments, burners, and circulating passage ways of the appliance to be kept clean. To clean the logs, use a soft paint brush, and to clean the burner compartment, use a vacuum cleaner but take all the logs, vermiculite and embers out.
  • Page 25 This warranty defines the obligation and liability of CFHM with respect to the Luxor gas appliance and any other warranties expressed or implied with respect to this product, its components, or accessories are excluded.

Table of Contents

Save PDF