Table of Contents
Advertisement
XX074
V1411X-DVC, V1411J-DVC, V1410X-DVC
Variable-Speed Keypads
Vicon Industries Inc. does not warrant that the functions contained in this
equipment will meet your requirements or that the operation will be entirely
error free or perform precisely as described in the documentation. This
system has not been designed to be used in life-critical situations and
must not be used for this purpose.
Copyright © 2002 Vicon Industries Inc. All rights reserved.
Product specifications subject to change without notice.
Vicon and its logo are registered trademarks of Vicon Industries Inc.
VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK 11788
TEL: 631-952-CCTV (2288) FAX: 631-951-CCTV (2288) TOLL FREE: 800-645-9116
24-Hour Technical Support: 800-34-VICON (800-348-4266)
UK: 44/(0) 1489-566300 INFOFAX: 800-287-1207 WEB: www.vicon-cctv.com
Vicon Part No. 8009-8074-02-01
Rev 703 Section 9
Advertisement
Table of Contents
Related Manuals for Vicon V1411X-DVC
Summary of Contents for Vicon V1411X-DVC
- Page 1 V1411X-DVC, V1411J-DVC, V1410X-DVC Variable-Speed Keypads Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed to be used in life-critical situations and must not be used for this purpose.
-
Page 4: Table Of Contents
Contents Introduction .........................1 Configuration & Installation ....................2 Passcode Setup........................5 Keypad Setup ........................6 Operation ..........................8 Operating Modes ............................8 Alarms ................................8 Auxiliary Function Control ..........................8 Communication Failure ..........................9 Crosspoint Reset............................9 Lens Operation ...............................9 Presets................................9 Manual Switching ............................10 Salvos and Tours............................10 Sequential Switching ...........................10 Using the Joystick............................11 Technical Information .......................12 Shipping Instructions .......................13... -
Page 6: Introduction
Introduction Note: Read all of the instructions completely before installing or operating this equipment. The information in this manual covers installation, programming and operation for the V1411X-DVC Variable- Speed Keypad and two alternate configurations, the V1411J-DVC and V1410X-DVC. The installation procedures should only be performed by a qualified technician using approved materials in accordance with national, state and local wiring codes. -
Page 7: Configuration & Installation
Warning: Do not connect this unit to a power source until all connections are complete. In the installation figures that follow, the V1411X-DVC is shown. The figures are applicable to all three variations of the keypad (V1411X-DVC, V1411J-DVC and V1410X-DVC). The keypad is shipped with the following accessories: •... - Page 8 NOVA To use any of Vicon’s NOVA control systems, including the V1411 and V1411-EXP Video Switchers with Telemetry Control, with the keypad, you will use NOVA configuration. You may connect multiple keypads in this configuration, as shown in the example below.
- Page 9 In + on the first keypad’s RJ-45 box to Command In + on the second keypad’s termination box and so forth. NOVA Control System VICON 110 VAC or 230 VAC POWER SUPPLY (Refer to Technical RJ-45 Information for details) TERMINATION RJ45-to-RJ45 CABLE V1411X-DVC V1411X-DVC 4 • Configuration & Installation XX074-02-01 Rev 703 Variable-Speed Keypad...
-
Page 10: Passcode Setup
To delete a user passcode only, enter all zeroes for that user passcode. To recover a lost manager passcode (and retain the programmed user passcodes), contact Vicon Technical Support at 1- 800-645-9116 (U.S.) or +44 (0) 1489 566330 (U.K.). -
Page 11: Keypad Setup
Note: If an alarm occurs when there is no user logged on to a passcoded keypad, the passcode line of the display shown above will alternate between Passcode? ---- and Alarm. Enter a valid passcode and acknowledge the alarm as discussed on page 8. To manually log off of the keypad, perform the following keystrokes PROG PROG... - Page 12 Setup Parameter Description Choices Display Contrast Sets the LCD contrast. (view the LCD window) Address Sets the address for this keypad. (for Standalone mode) 1-64 (for NOVA mode) Baud Rate Sets the communication baud rate. All keypads in your 1200, 2400, 4800, 9600 NOVA system must have the same baud rate! baud, 19.2 kBaud Joystick Profile...
-
Page 13: Operation
Operation Operating Modes If passcodes are not active, mode 1 is automatically entered after power is applied or if the keypad is reset. If passcodes are active, the passcode entry screen will display upon applied power or if the keypad is reset. Refer to Indicators in Display in the Technical Information chapter for LCD status messages. -
Page 14: Communication Failure
Communication Failure Note: The procedure to clear all failure announcements is applicable for V1500 systems only. If the com fail is on a If the com fail is on To clear all This selects This This camera that is NOT CANCEL CANCEL CANCEL... -
Page 15: Manual Switching
Manual Switching Selecting a Monitor Selecting a Camera Clearing Input Errors CANCEL Press Press Enter monitor number Enter camera number Press Press Salvos and Tours Note: Salvos and tours are not available in all control systems. Refer to your control system documentation if necessary. -
Page 16: Using The Joystick
Adding All Cameras PROG PROG Press & Hold Release Press Press Press Deleting All Cameras Perform these steps if you are not already in Mode 2. PROG PROG Press & Hold Release Press Press Press Using the Joystick Autopanning Zooming with the Joystick Panning and Tilting Note: Manual pan operations Use the joystick. -
Page 17: Technical Information
Lens Speed Key: Changes lens speed. Dependent upon receiver. Joystick: V1411X-DVC and V1410X-DVC: Causes pan-and-tilt mechanism to pan and tilt at varying speed. V1411J-DVC: Causes pan-and-tilt mechanism to pan and tilt at varying speed. Used to zoom in/out at a selected fixed speed. -
Page 18: Shipping Instructions
Shipping Instructions Use the following procedure when returning a unit to the factory: 1. Call or write Vicon for a Return Authorization (R.A.) at one of the locations listed below. Record the name of the Vicon employee who issued the R.A. - Page 19 Vicon Industries Inc. Offices Corporate Headquarters 89 Arkay Drive Hauppauge, New York 11788 631-952-CCTV (2288) 800-645-9116 Fax: 631-951-CCTV (2288) Infofax: 800-287-1207 Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) 1489 566300 Fax: +44 (0) 1489 566322...
Need help?
Do you have a question about the V1411X-DVC and is the answer not in the manual?
Questions and answers