Table of Contents
Advertisement
_ _ _ _ LEAR SIEGLER, INC.
DATA PRODUCTS DiViSION
'Table 3-2. ADM 3A Set-Up Mode Functions and Control Codes (continued)
FUNCTION
CONTROL KEYS
DESCRIPTION
Change Set-Up Selection
ICTRL
[0
MOVE~S
cursor right to change value of function.
to option right of cursor.
Mc)ve Up To Next
ICTRL
[KJ
Goes back to previous set-up parameter.
Prl~vious
Set·Up Mode
Entry
Mc)ve Down To Next
~
Continues to next set-up mode parameter.
Set·Up Entry
features, and to set or change terminal parameters
when required through kevboard commands. The
set-up features, which reside in non-volatile
EEROM, are displayed on line 24 (status line). The
set-up mode is accessible only from the keyboard
~ding
down [ SHIFT
I
key and pressing the
IE]
key. The setup key is located in the
recessed area under the metal plate to the left of
the keyboard (Figure 2-7, page 2-9). Table 3-2,
page
3-4 provides a list of set-up mode keyboard
commands that control set-up mode operations.
The set-up functions may be changed in any
sequence.
3.3.2
set
Termlna! Configuration
Perameters
To set configuration parameters after receiving
the AIlM 3A unit:
1. Power on the ADM SA terminal by setting
the ON/OFF switch to ON position.
2. Upon power-up, a reverse block cursor ahould
appear in the left-most column on line 1 when
the terminal has passed its diagnostics.
3. Unscrew the metal plate (located in the
recessed area to the left of keyboard) to access
l]SETUP I
key.
4.
En
t
e r "'S~H""""IF""'"'"=T"""S~E=-=T~U~P~
hoI d dow n
SHIFT
key, then press SETUP key).
5. The first set-up mode entry, HHDX FDX" is
displayed on line 24. You can now set or
change terminal
parameters.
As
each
function is called up, the cursor is positioned
over one of the available selections. (i.e. YES
or NO).
3-5
To change the value for any function, press
I
CTBb[JJ
or
I CTRLrnJ
until the CW"8Or is
positioned over the desired value.
6. To display the next function on the lilt of aet-
up mode functions, press
I
CTRLI1J.
For
example, the first function
:iJJrl~ed
is
uHDX FDX." Pressing
l
C
will
remove uHDX FDX" from the acreen and
display the next function UBA
un
RATE."
(See
Table
3-3,
page
3-8 for a complete list
of configuration parameters available with
the ADM SA.)
To
bac~nd
display the previous function,
press
tOO.
After all parameters have
been viewed, the terminal returns to the first
set-up mode entry, uHDX FDX."
7.
The set-up functions may be changed in any
sequence; they do not need to be .elected in
order of display. All the selected functions
will remain in effect until the terminal is
turned off. Anytime power is first turned on,
the cursor is positioned over the individual
configurations which were aet the last time
the set-up mode was aaved.
(See
Pararraph
8.3.4, below).
~~.3.3
Exiting Set-Up Mode
To exit set-up mode, press J~S~H=IFT~""ls~E~TUP~~1
which is the method used to enter set-up mode.
31.3.4 Save Current Terminal
Configuration Values
To
save current terminal configuration values
after setting the desired parameters, enter
Advertisement
Table of Contents
