Advertisement
How
to
use the Unicouple
on convertible
models
Before
operating
yourdishwasher
the
first
WmL.
Attach the Aerator FkKx3t
Adapter
The special aerator faucet adapter
supplied with your dishwasher
must be assembled to the sink
faucet spout before you can use
yo~r dishwasher.
How
to
connect
t he
1. Pull Unicouple and its hoses
from storage compartment located
at rear of dishwasher and attach it
to the faucet adapter.
The faucet adapter is designed to
fit standard spouts having internal
or external threads. You will find
the adapter and two washers in
the "Hardware for Installation"
packet in your dishwasher.
To install faucet adapler, first
remove the old aerator or trim ring
on your faucet spout.
If faucet has external threads:
Insert the thinner of the two
washers into the faucet adapter
and attach it to the faucet spout.
If faucet has internal threads:
==Q
$EiB
p v
\r
Insert both washers into the faucet
adapter and attach it to the faucet
spout.
If
the
faucet
adapter
threads
do
not match your faucet spout,
your local hardware or plumbing
supply store normally has
additional fittings to adapt your
faucet spout to the special aerator
faucet adapter.
MNIE: A sink spray attachment
.k2se
can burst
if it is installed on
the same sink with your dish washe~
M.@ suggest that you disconnect
the
sink spray attachment if your
sink has one am' plug the hole.
2. Attach the Unicouple connector
to the faucet adapter by depressing
collar at the top of the connector.
When Unicouple is all the way up
onto the adapter, release the collar.
It will then snap into position to
lock the Unicouple in place.
The Unicouple's small hose carries
water from the faucet to the
dishwasher. Its large hose carries
drain water to the sink. Be sure
drain hose is pointing toward the
sink bowl drain opening and the
sink drain is open for water that
will drain from your dishwasher. If
your dishwasher drains into a dis-
poser, operate the disposer until it
is completely empty before start-
ing the dishwasher.
3. Turn hot water fully on before
starting the dishwasher.
The Faucet-Flo nozzle is part of
the Unicouple connector. Operate
the nozzle by depressing the
pressure release lever on the side
of the Unicouple connector. You
will find the Faucet-Flo nozzle
useful for several reasons:
@It allows you to flush cold water
out of the hot water line so that
you can better regulate your water
temperature.
@It allows you to test the
temperature of the water before
starting your dishwasher.
If you need fresh water for
personal use:
Disconnect the Unicouple.
Draw your fresh water directly from
your faucet.
Do not disconnect the Unicouple
while the dishwasher is operating.
How to disconnectthe
Unicoupiefrom faucet
adapter.
't.
T urn off the hot water.
2. Release the water pressure by
depressing the pressure release
lever. This relieves water pressure
and protects you, and the room,
from severe splashing.
3. Release Unicouple from faucet
by depressing the coliar at the top
of the Unicouple connector.
How
to disconnect
your
convertible
dishwasher
1. Remove the power cord
plug
from the wall receptacle.
2. DisconnectUnicouplefrom
faucet adapter.
3. Shakeexcesswater out of
Unicoupleand return it and its
hosesto the dishwasherstorage
compartment.
NOTE:W/henmotor stops at the
end of the final
rinse, the Uni-
coupie can be disconnected and
returned to storage.
Advertisement
