Table of Contents
Advertisement
AQUA STAR
KIT # HRR502
Assembly Instructions
WARRANTY
Herr Engineering Corp. guarantees this kit to be free from defects in both materials and workmanship at the time of
purchase. This warranty does not cover any component damaged buy use or modification. In no case shall Herr
Engineering Corporation's liability exceed the original cost of the purchased kit. Further Herr Engineering Corp.
reserves the right to change or modify this warranty without notice.
In that Herr Engineering Corporation has no control over the assembly or use, no liability shall be assumed or
accepted for any damage resulting from the use by the user during construction of the kit or the use of the final user
assembled product. By the act of building this kit and/or using the final user assembled product, the user accepts all
liability.
If the buyer and/or user is not prepared to accept all of the liability associated with this product, he is advised to
immediately return this kit in new and unused condition to the place of purchase for a full refund.
Herr Engineering Corp.
Award Winning Model Designs
™
A Division of SIG Mfg. Co., Inc.
P.O. Box 520 • Montezuma, Iowa 50171-0520
Phone: (641)623-5154 • Website: www.iflyherr.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Herr Engineering AQUA STAR HRR502
Summary of Contents for Herr Engineering AQUA STAR HRR502
-
Page 1: Assembly Instructions
Assembly Instructions WARRANTY Herr Engineering Corp. guarantees this kit to be free from defects in both materials and workmanship at the time of purchase. This warranty does not cover any component damaged buy use or modification. In no case shall Herr Engineering Corporation’s liability exceed the original cost of the purchased kit. -
Page 2: Kit Contents
Notes about the laser cut parts 1...The first thing that you need to do is to identify and mark the part numbers on the laser cut parts using the drawings on the following pages as a guide. 2...It is possible that several of the laser cut parts may not be completely cut through. If this is the case you can free the part from the sheet quickly using an X-acto knife. - Page 3 Additional Items Required ( Not Included in Kit) Note: These are parts that we have used and are familiar with. There are many other brands available and you may substitute other items that you are more comfortable with or have on hand. Qty.
- Page 4 Page 4...
-
Page 5: Building Instructions
Building Instructions: General Note: Cover the plans with wax paper before assembling your model to prevent the parts from sticking to the plan. Building the Tail Surfaces: 1...Join R-1 and R-2 together over the plan. Temporarily hinge the rudder to the fin. Do not glue the hinges at this time. 2...Join parts S-2 to each end of S-1. - Page 6 Building the Left Wing: 27...Pin the lower 1/4” sq. spar and the trailing edge to the left wing plan. 28...Cut the lower 1/16” sheet for the lower inboard end of the wing and glue in place between the trailing edge and the spar. 29...Glue the lower plywood dihedral brace to the front of the lower spar.
-
Page 7: Final Assembly
56...Mark the mounting plates where the tip floats will attach and remove the covering from this location. Glue the tip floats to the mounting plates. Cut the 1/4” sq. strip to make triangular braces and glue into position. 57...Cut the 1/8” dowels to length. Remove the covering from the mount plate at the dowel location and glue the dowels into position. - Page 9 Herr Engineering Corp. Kit #502 Aqua-Star Correction Sheet, Revision #5 #1...Be sure to mount the engine far enough forward on the mount so the rear of the muffler does not interfere with the firewall. #2...Several of the rudder / fin parts are numbered wrong on the sheet layouts on page 4 of the instruction book, but you should have no difficulty identifying them by laying them on the plan.
Need help?
Do you have a question about the AQUA STAR HRR502 and is the answer not in the manual?
Questions and answers