Download Print this page
Barco DCS-200 Quick Start Manual

Barco DCS-200 Quick Start Manual

2 channel
Hide thumbs Also See for DCS-200:

Advertisement

Quick Links

Quick Start Guide

Visibly yours
Menu Display
Use ADJUST knob, plus
• Counter-clockwise: scroll down
SEL and ESC buttons to
menu tree, or decrement values.
navigate menus.
• Clockwise: scroll up menu tree,
or increment values.
P R O G R A M :
N E X T :
ESC
Press to exit a menu
without making changes,
cancel an operation, or
answer "No" to a query.
Quick Setup and Operations
The following list summarizes DCS-200 setup and
operations. For error-free installation, always
refer to the listed section in the User's Guide.
Connect Power — Ensure that power is properly
1
connected to the DCS-200. (Chapter 3, "Power
Installation")
Connect Inputs — Connect all analog, DVI, and
2
SDI input sources to the DCS-200. (Chapter 3,
"Signal Installation")
Connect Outputs — Connect the output(s) of the
3
DCS-200 to your projector(s) or other target devices.
(Chapter 3, "Signal Installation")
Power On — Turn on power to the DCS-200, your
4
projector(s), and to all peripheral equipment.
(Chapter 4, "Power-Up Initialization")
Adjust
Press to enter a menu,
change or accept a
parameter, or answer
"Yes" to a query.
R G B
1 0 2 4 x 7 6 8 @ 5 9 . 9 4
S D I
N T S C ( 4 8 0 i )
Adjust
FRZ
Press to freeze or
Press to pend or initiate a black transition.
un-freeze current
Black Auto Take mode affects function
Program source.
(User Preferences). Blinking = Pending.
Lit solid = frozen.
Factory Reset – When using a DCS-200 for the
5
first time, perform a factory reset. (Chapter 4,
"Factory Reset")
Launch GUI — (Optional) Connect your laptop to the
6
DCS-200, log onto the DCS-200 using its IP address,
and launch the GUI. (Chapter 5, "GUI Operations")
Set Output Format — Set the desired output
7
resolution and frame rate. (Chapter 4, "Output
Format")
Enable Test Pattern — Turn on a test pattern, verify
8
an image, and adjust as required. When complete,
turn off the pattern. (Chapter 4, "Test Pattern")
Save Output Configuration — After completing all
9
output adjustments, save the output configuration.
(Chapter 4, "Save Output Config")
Select and Adjust Input — Select an input, and
10
perform the necessary image adjustments. (Chapter
4, "Input Menu")
Save Input Configuration — After completing all
11
adjustments for an input, save the input configuration.
(Chapter 4, "Save Input Config")
Barco Media and Entertainment
11101 Trade Center Drive
Rancho Cordova, CA
95670 • USA
SEL
Inputs Section
Sources 1-6: Analog
Sources 7-8: DVI or Analog
SDI: SD-SDI or HD-SDI
LOGO: Full screen capture
SEL
1
2
3
4
ESC
Effects
FRZ
BLACK
BLACK
Press to pend or initiate a key transition.
(User Preferences). Blinking = Pending.
Lit solid = Black on Program.
Technical Support:
Button States
Off: Input not selected
Blinking (fast): Input being acquired
Blinking (slow): Input "pending" for transition
Lit solid: Input on Program
Inputs
5
6
7
8
SDI
LOGO
KEY
TAKE
KEY
Key Auto Take mode affects function
Lit solid = Key on Program.
Repeat for Each Input — Repeat steps 9 and
12
10 for each input that you have connected to the
DCS-200.
Adjust Key Source — As required, select the
13
desired key source and adjust its clip, gain and
opacity. (Chapter 4, "Using Keys")
Adjust System Parameters — Adjust parameters
14
such as transition time, display brightness, user prefs.
(Chapter 4, "Trans Time," "System Menu")
Save System Configuration — After completing all
15
system adjustments, save the system configuration.
(Chapter 4, "Save System State")
Enable Remote Control — (Optional) Connect
16
Ethernet or Serial communications, and issue desired
commands. (Appendix B, "Remote Control")
Ready to Roll — With all output, input and system
17
configurations saved, press the desired input button,
and press TAKE.
Toll Free:
+1 (888) 414-7226
Fax:
+1 (916) 859-2515
+1 (866) 374-7878
Website:
www.barco.com
DCS-200
TAKE
Press to mix the selected input
to Program, or to execute a
pending key or black transition.
Use the Setup Menu to adjust
the transition time.
After each TAKE,
NOTE
Program and pending
sources flip-flop.
P/N 26-0604014-00 Rev 00

Advertisement

loading

Summary of Contents for Barco DCS-200

  • Page 1: Quick Start Guide

    TAKE. (Chapter 3, “Signal Installation”) Save Input Configuration — After completing all Power On — Turn on power to the DCS-200, your adjustments for an input, save the input configuration. projector(s), and to all peripheral equipment. (Chapter 4, “Save Input Config”) (Chapter 4, “Power-Up Initialization”)
  • Page 2: Status Menu

    PCs, VTRs, and cameras. The connector’s analog pins can be HD-SDI source. provided. Both have the analog preview communications with DCS-200. Use the Use breakout cables as required. accessed with a breakout cable, or same resolution, and both monitor.