2u triple lcd video monitor with analog inputs and loop-throughs, optional additional input sections, and optional sdi inputs and outputs with converted to analog output
Hd/sdi high-res video monitors with 4.3" high-resolution lcd video displays, selectable 16:9 or 4:3 aspect ratio, sdi or hd-sdi inputs and buffered/equalized outputs (on bnc), and sdi lock indication leds (16 pages)
2u quad lcd video monitor with four 4" lcd video displays, eight composite video inputs (on bnc) with a/b switching, eight loop-through outputs (on bnc), and option for adding sdi inputs (16 pages)
Hdmon series multi-format high-definition lcd screen with osd controls, two hd/sd-sdi in and buffered out, dvi in, xga in, y/pb/pb in, composite in, s video in, tally, and remote pc control through ethernet or rs-232 ports (32 pages)
MON3-2A 2U Triple LCD Video Monitor With Analog Inputs and Loop-throughs, Optional Additional Input Sections, and Optional SDI Inputs and Outputs with Converted to Analog Output Document P/N 821521 Rev-B.5 User Manual CONTENTS Title and Contents ............Introduction .................. Section 1: General Features and Specifications ...
Important Safety Instructions 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. Do not install near any heat source such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Page 4
MON3-2A Front Panel Description The MON3-2A is a 2RU chassis containing three 4 inch Active Matrix TFT LCD’s. Each LCD is back lit with a cold cathode fluorescent tube. The LCD can display standard NTSC or PAL analog video signals. A second analog video input can be selected with the optional Analog B Board.
Section 1: General Features and Specifications Applications The MON3-2A is ideally suited for monitoring of multiple video feeds in VTR bays, mobile production vehicles, news and transmission control rooms, and duplication and post production applications. Designed and manufactured in the U.S., the MON3-2A is backed by a strong warranty and a satisfaction guaranteed return policy.
Page 9
Contact PANORAMAdtv sales representative if there are any unexplained shortages. Power Requirements The MON3-2A is equipped with a world standard power supply that is capable of operating on 90-264 VAC @ 50-60 Hz. Power consumption is 12 watts, standard and 21 watts when all three MSDI SDI options are installed.
Page 10
Note: Descriptions of items 2 through 6 apply to each one of the three monitor sections (1 - 3). Power Indication - Green LED The Power Indicator glows green when mains power is connected to the MON3-2A. Individual display power switches (Item E, page 12), located on the rear panel control the on/off operation of each of the three associated displays.
Page 12
Section 2: Operation MON3-2A User Manual P/N 821521 Rev-B.5 Rear Panel Features Please refer to Figure-2c on the following page to familiarize yourself with the rear panel features of the MON3- 2A unit. The following sections describe these features and are referenced, by letter, to Figure-2c.
Page 14
Section 2: Operation MON3-2A User Manual P/N 821521 Rev-B.5 Rear Panel Features (Continued) CVBS Out - BNC Connector (MSDI-1 SDI Option) This connector supplies an analog CVBS encoded signal derived from the SDI input. Automatic standards sensing is accomplished by detecting 525 or 625 line signals. 525 line SDI input signals are encoded as an NTSC output.
Page 18
NOTE: Ensure the LED power supply provides +5 to +12VDC. Non-Isolated Operating the Tally LEDs in the non-isolated configuration uses the MON3-2A internal power supply to provide the tally LED voltage. Connect your tally closures as shown in Figure-3b to the respective MON3-2A tally connections.
This section explains the procedures for field upgrading your unit for the MSDI-4 SDI option. We advise you to work with the unit on a clean, well lighted work bench. Ensure the MON3-2A is disconnected from the power mains. Remove top cover. Retain screws for later reassembly.