Table of Contents
Advertisement
ENGLISH
@
Warning! Shock hazard. Do not allow any liq-
uid to get inside charger. Never attempt to open
the battery pack for any reason. If the plastic
housing of the battery pack breaks or cracks,
return to a service center for recycling.
STATE OF CHARGE INDICATOR (FIGURE B)
The back of the battery is equipped with a state of charge in-
dicator. This can be used to display the current level of charge
in the battery during use and during charging. It does not
indicate tool functionality and is subject to variation based on
product components, temperature and end-user application.
Checking state of charge during use:
Press the state of charge indicator button (B1).
u
The four LED's (B2) will illuminate indicating the percent of
u
charge in the battery. See chart in figure B.
If LED light does not lluminate, charge battery.
u
Note! This battery is designed to not operate when a charge
below 20% of its capacity is reached. After the battery charge
is depleated, the toll will not operate until after the battery has
been recharged.
@
Installing and removing the battery pack
WARNING! Make certain the tool is switched off
before removing or installing battery.
TO INSTALL BATTERY PACK:
Insert battery pack into tool until fully seated and an audible
click is heard (figure C). Make sure battery pack is fully seated
and fully latched into position.
TO REMOVE BATTERY PACK:
battery release button in the back of the battery pack and pull
@
battery pack out of tool.
WARNING! Before assembly, make sure that
the tool is switched off and the battery has been
removed.
Tube assembly (fig. D)
To attach the inner tube to the sweeper, line up the tube with
the sweeper housing as shown in figure D. Push the tube into
the sweeper housing until the lock button engages the lock
hole in the tube. Repeat this process for the outer tube.
Note! Ensure the sweeper is switched off and the battery is
removed before attaching or removing the sweeper tubes. The
tube assembly must be assembled to the housing before use.
Opearation
8
(Original instructions)
always wear safety glasses. wear A filter mask if the operation
is dusty. use of rubber gloves and substantial footwear is rec-
@
ommended when working outdoors. For household use only.
WARNING! Cut Hazard. When turning the tool
off for tube installation or any other reason, wait
10 seconds for the fan to stop rotating before
disassembly.
Always switch off and remove the battery when:
The power supply cord has become damaged or entan-
u
gled.
You leave sweeper unattended.
u
Checking, adjusting, cleaning or working on sweeper.
u
Use sweeper only in daylight or good artificial light.
@
SWITCHING ON AND OFF (FIGURE E)
WARNING! Use both hands to grip the product
firmly when switching on.
To switch the sweeper on, slide the on/off switch forward.
To switch the sweeper off, slide the on/off switch back.
@
CAUTION! Do not point unit discharge at self or
bystanders.
POWER COMMAND (Figure F)
MAX POWER / MAX RUNTIME
The max power / max runtime feature (F1) is located on the
tool handle. It allows you to optimize the tools performance
and boost the power as needed.
To choose max power, rotate dial to setting 6.
u
To maximize runtime rotate dial to setting 1.
u
For a combination of both, rotate dial to setting from 2 to
u
5.
@
Sweeper Opearation
CAUTION! Always wear safety glasses. Wear
a filter mask if the operation is dusty. Use of
gloves, long pants and substantial footwear is
recommended. Keep long hair and loose clothing
away from openings and moving parts. THIS
SWEEPER IS FOR HOUSEHOLD USE ONLY.
Note! Ensure the sweeper is switched off and the battery is
removed before attaching or removing the sweeper tubes. The
sweeper tube must be assembled to the housing before use.
Install battery after assembly just prior to use.
Hold the sweeper with one hand as shown in figure G and
u
sweep from side to side with the nozzle several inches
above the hard surface. Slowly advance keeping the ac-
cumulated pile of debris in front of you.
Advertisement
Table of Contents
