Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
CDP4260-L/CDP4262-L/CDX4652-L/
CDP5560-L/CDP5562-L
LCD Monitor
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the Regional selection
box in the upper right corner of our website. "Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual"
Model No. VS15673/VS15674/VS15662/VS15663/VS15664
Advertisement
Table of Contents
Troubleshooting
Related Manuals for ViewSonic CDP4260-L
Summary of Contents for ViewSonic CDP4260-L
-
Page 1: Lcd Monitor
Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website. -
Page 2: Compliance Information
Compliance Information NOTE: This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on unit. FCC Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 3 CE Conformity for European Countries The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC. Following information is only for EU-member states: The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).
- Page 4 Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum...
-
Page 5: Safety Precautions
Safety Precautions FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONITOR: • DO NOT REMOVE MONITOR BACK COVER. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks. Refer all servicing to qualified service personnel. -
Page 6: Recommended Use
CAUTION: Immediately unplug your monitor from the wall outlet and refer servicing to qualified service personnel under the following conditions: • When the power supply cord or plug is damaged. • If liquid has been spilled, or objects have fallen into the monitor. •... -
Page 7: Table Of Contents
6.2. Troubleshooting ......26 3.1.1. Using COMPONENT 7. Technical Specifications ....27 video input ......10 7.1. CDP4260-L / CDP4262-L ..... 27 3.1.2. Using HDMI video input ..10 7.2. CDX4652-L ........29 3.2. Connecting a PC ......11 7.3. CDP5560-L / CDP5562-L ..... 31 3.2.1. -
Page 8: Copyright Information
Serial Number: Purchase Date: Product disposal at end of product life ViewSonic respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic website to learn more. USA & Canada: http://www.viewsonic.com/company/green/recycle-program/ Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/... -
Page 9: Unpacking And Installation
Unpacking and Installation 1.1. Unpacking • This product is packed in a carton, together with the standard accessories. • Any other optional accessories will be packed separately. • Due to the size and weight of this display it is recommended for two people to move it. •... -
Page 10: Installing And Removing Table Stands (Optional)
1.4. Installing and Removing Table Stands (optional) To install table stands: 1. Ensure your display is powered off. 2. Spread a protective sheet on a flat surface. 3. Grab the carrying handles and place the display face-down on the protective sheet. 4. -
Page 11: Vesa Grid
4. For the wall-mounting kit, use M6 mounting screws (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely. 1.5.1. VESA Grid 400(H) x 200(V) mm CDP4260-L / CDP4262-L / CDX4652-L 200(H) x 200(V) mm 400(H) x 400(V) mm... -
Page 12: Parts And Functions
Parts and Functions 2.1. Control Panel CDP4260-L/CDP4262-L/CDP5560-L/CDP5562-L: MUTE INPUT MENU CDX4652-L: MUTE INPUT MENU... - Page 13 POWER button Remote control sensor and power status Use this button to turn the display on or put the indicator display to standby. • Receives command signals from the remote control. MUTE button • Indicates the operating status of the display: Switch the audio mute ON/OFF.
-
Page 14: Input/Output Terminals
2.2. Input/Output Terminals CDP4260-L/CDP4262-L/CDP5560-L/CDP5562-L: 5 6 7 9 10 11 12 14 15 CDX4652-L: 5 6 7 9 10 11 12 14 15... - Page 15 To remotely control your A/V device via this display, refer to page 14 for IR Pass Through Component YPbPr video source input. connection. SPEAKER SWITCH RS232C OUT Internal speaker on/off switch (CDP4260-L/ RS232C network output for the loop-through CDP4262-L/CDP5560-L/CDP5562-L). function. External speaker on/off switch (CDX4652-L). RS232C IN AUDIO IN RS232C network input for the loop-through function.
-
Page 16: Remote Control
2.3. Remote Control [DISPLAY] button Press to turn on/off the information OSD displayed on the upper right corner of the screen. 2.3.1. General functions [ ] button • Press to move the selection left in OSD menu. • Press to decrease the value in OSD menu. POWER •... -
Page 17: Inserting The Batteries In The Remote Control
2.3.2. Inserting the batteries in the remote 2.3.4. Operating range of the remote control control Point the top of the remote control toward the The remote control is powered by two 1.5V AAA display’s remote control sensor when pressing a batteries. -
Page 18: Connecting External Equipment
Connecting External Equipment 3.1. Connecting External Equipment (DVD/VCR/VCD) 3.1.1. Using COMPONENT video input Audio Out COMPONENT Out (YPbPr) DVD / VCR / VCD [AUDIO IN] [COMPONENT IN] (Pr/Pb/Y) 3.1.2. Using HDMI video input DVD / VCR / VCD HDMI Out [HDMI IN]... -
Page 19: Connecting A Pc
3.2. Connecting a PC 3.2.1. Using VGA input VGA Out D-Sub 15 pin Audio Out [AUDIO IN] [VGA IN] [VGA AUDIO IN] 3.2.2. Using DVI input DVI Out Audio Out [AUDIO IN] [DVI IN] [VGA AUDIO IN] 3.2.3. Using HDMI input HDMI Out [HDMI IN]... -
Page 20: Connecting Audio Equipment
3.3. Connecting Audio Equipment 3.3.1. Connecting external speakers External speakers 3.3.2. Connecting an external audio device Audio In Stereo Ampli er [AUDIO OUT]... -
Page 21: Connecting Multiple Displays In A Daisy-Chain Configuration
3.4. Connecting Multiple Displays in a Daisy-chain Configuration You can interconnect multiple displays to create a daisy-chain configuration for applications such as a video wall. NOTE: Maximum 25 displays (5x5) can be used in a daisy-chain configuration. 3.4.1. Display control connection Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2. -
Page 22: Ir Connection (Optional)
3.4.4. IR connection (optional) DISPLAY 1 DISPLAY 2 External IR Receiver [IR IN] [IR OUT] [IR IN] [IR OUT] POWER VIDEO AUDIO SMART SOURCE SOURCE ON/OFF INPUT CHANGE CONTRAST BRIGHTNESS DISPLAY MENU AUTO EXIT ADJUST VOL UP VOL DOWN OPTION NOTE: This display’s remote control sensor will stop working if the [IR IN] is connected. -
Page 23: Osd Menu
OSD Menu 4.2. OSD Menu Overview An overall view of the On-Screen Display (OSD) 4.2.1. PICTURE menu structure is shown below. You can use it as a reference for further adjusting your display. PICTURE 4.1. Navigating the OSD Menu BRIGHTNESS CONTRAST SHARPNESS BLACK LEVEL... -
Page 24: Screen Menu
USER COLOR 4.2.2. SCREEN menu With this function you can adjust the color tones of the image precisely by changing the R (Red), SCREEN G (Green) and B (Blue) settings independently. AUTO SETUP AUTO ADJUST NOTE: This item is functional only when {COLOR H POSITION V POSITION TEMPERATURE} is set to {USER}. -
Page 25: Audio Menu
INPUT RESOLUTION This function allows you to optimize the picture display on screen. The following zoom modes are Set the resolution of the VGA input. This is only available for: required when the display is unable to detect the • PC mode: {FULL} / {NORMAL} / {CUSTOM} / VGA input resolution correctly. -
Page 26: Pip Menu
4.2.4. PIP menu Main Picture HDMI YPbPr Video Sub Picture PIP MODE HDMI PIP SIZE SMALL YPbPr PIP AUDIO MAIN AUDIO PIP H POSITION Video PIP V POSITION SUB INPUT VIDEO PIP RESET (O: PIP function available, X: PIP function unavailable) By pressing the [PIP ON/OFF] button on the remote control, you can change the mode in the... - Page 27 You can select: 4. For more schedule settings, press [EXIT] button and then repeat the steps above. A check mark • The time for the display to turn on and turn off. in the box next to the number of the schedule •...
-
Page 28: Configuration2 Menu
4.2.6. CONFIGURATION2 menu • {NORMAL} - All displays can be operated normally by the remote control. • {LOCK} - Lock the remote control function CONFIGURATION2 of this display. To unlock, press and hold the LANGUAGE [DISPLAY] button on the remote control for 5 OSD TURN OFF OSD H POSITION (five) seconds. -
Page 29: Configuration3 Menu
• POSITION - Select the position of this display 4.2.7. CONFIGURATION3 menu in the screen matrix. • FRAME COMP. - Choose to turn the frame CONFIGURATION3 compensation function on or off. If turned on, POWER SAVE HEAT STATUS the display will adjust the image to compensate SCREEN SAVER for the width of the display bezels in order to SIDE BORDER COLOR... -
Page 30: Advanced Option
SCREEN SAVER 4.2.8. ADVANCED OPTION menu Choose to enable the panel saving functions to reduce the risk of the “image persistence”. ADVANCED OPTION SCREEN SAVER INPUT CHANGE NORMAL TERMINAL SETTING SCAN CONVERSION COOLING FAN AUTO COLOR SYSTEM BRIGHTNESS SCAN MODE SERIAL CONTROL MOTION LAN SETTING... - Page 31 SCAN CONVERSION • DHCP - Choose to enable or disable the DHCP function. If enabled, the display will be assigned Choose to enable or disable the IP (Interlace to IP address, Subnet mask and Default gateway Progressive) conversion function. automatically. If disabled, you will be prompted •...
-
Page 32: Input Mode
Input Mode VGA Resolution: Active Resolution Standard Refresh Rate Pixel Rate Aspect Ratio Stand for Mode Resolution H Pixels V Lines 60 Hz 25.175 MHz 72 Hz 31.5 MHz Video Graphic Array 75 Hz 31.5 MHz Wide Video Graphic WVGA 70 Hz 33.75 MHz 16:9... -
Page 33: Cleaning And Troubleshooting
Cleaning and Troubleshooting 6.1. Cleaning When Using the Display • Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the display is usually very hot due to the high temperature of exhaust air being released through the ventilation holes. -
Page 34: Troubleshooting
6.2. Troubleshooting Symptom Possible Cause Remedy No picture is displayed 1. The power cord is disconnected. 1. Plug in the power cord. 2. The main power switch on 2. Make sure the power switch is the back of the display is not switched on. -
Page 35: Technical Specifications
Technical Specifications 7.1. CDP4260-L / CDP4262-L Display: Item Specifications Screen Size (Active Area) 42” LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.4845 (H) x 0.4845 (V) [mm] Displayable colors 1.06 Billion colors Brightness (typical) - Page 36 General: Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 150W Power Consumption (typ.) 120W Power Consumption (Standby & Off) <0.5W (RS232 in active) Dimensions (With Stand) [W x H x D] 965.8 x 601.4 x 400 mm Dimensions (Without Stand) [W x H x D] 965.8 x 558.8 x 69 mm Weight (With Stand) 20.6 Kg...
-
Page 37: Cdx4652-L
7.2. CDX4652-L Display: Item Specifications Screen Size (Active Area) 46” LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.17675 (H) x 0.53025 (V) [mm] Displayable colors 16.7M colors Brightness (typical) 500 cd/m2 Contrast ratio (typical) 3500:1 Viewing angle 178 degrees... - Page 38 General: Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 200W Power Consumption (typ.) 120W Power Consumption (Standby & Off) <0.5W (RS232 in active) Dimensions (With Stand) [W x H x D] 1023.98 x 629.41 x 400 mm Dimensions (Without Stand) [W x H x D] 1023.98 x 578.57 x 125.7 mm Weight (With Stand)
-
Page 39: Cdp5560-L / Cdp5562-L
7.3. CDP5560-L / CDP5562-L Display: Item Specifications Screen Size (Active Area) 55” LCD Aspect Ratio 16:9 Number of pixels 1920 (H) x 1080 (V) Pixel pitch 0.63 (H) x 0.63 (V) [mm] Displayable colors 1.06 Billion colors Brightness (typical) 700 cd/m2 (CDP5562-L) 450 cd/m2 (CDP5560-L) Contrast ratio (typical) 1300:1... - Page 40 General: Item Specifications Power Supply AC 100 ~ 240V, 50 ~ 60Hz Power Consumption (Max) 190W Power Consumption (typ.) 130W Power Consumption (Standby & Off) <0.5W (RS232 in active) Dimensions (With Stand) [W x H x D] 1247 x 758.2 x 400 mm Dimensions (Without Stand) [W x H x D] 1247 x 717.8 x 70 mm Weight (With Stand) 32.6 Kg...
-
Page 41: Other Information
(Mexico) Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16 Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico Latin America www.viewsonic.com/la/ T= 0800-54565 soporte@viewsonic.com... -
Page 42: Limited Warranty
If a product proves to be defective in material or workmanship during the war- ranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components. - Page 43 Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be li- able for: 1. Damage to other property caused by any defects in the product, damages based upon inconvenience,...
-
Page 44: Mexico Limited Warranty
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business relationships, or other commercial loss, even if advised of the possibility of such damages. - Page 45 Av Ferrocarril Sonora #3780 L-C 381 Brea Canyon Road, Walnut, CA. 91789 USA Tel: 800-688-6688 (English); 866-323-8056 (Spanish); Col 20 de Noviembre Tijuana, Mexico Fax: 1-800-685-7276 E-Mail: http://www.viewsonic.com 4.3: ViewSonic Mexico Limited Warranty Page 2 of 2 CD_LW02 Rev. 1A 06-25-07...