Konwin Home GD9315BCW-FP Owner's Manual
  1. Manuals
  2. Brands
  3. Konwin Home Manuals
  4. Heater
  5. GD9315BCW-FP
  6. Owner's manual

Konwin Home GD9315BCW-FP Owner's Manual

Infrared zone heating system
Hide thumbs

Advertisement

Table of Contents

INFRARED ZONE HEATING SYSTEM
OWNER'S MANUAL
Model No. GD9315BCW-FP
PLEASE SAVE THESE INSTRUCTIONS
WARNING: READ THIS OWNER'S MANUAL CAREFULLY BEFORE USE.

Advertisement

Table of Contents
loading

Summary of Contents for Konwin Home GD9315BCW-FP

  • Page 1 INFRARED ZONE HEATING SYSTEM OWNER’S MANUAL Model No. GD9315BCW-FP PLEASE SAVE THESE INSTRUCTIONS WARNING: READ THIS OWNER’S MANUAL CAREFULLY BEFORE USE.

  • Page 2: Important Instructions

    Thank you for choosing a Konwin Home Infrared Zone Heating System. This owner’s manual will provide you with valuable information necessary for the proper care and maintenance of your new product. Please take a few moments to thoroughly read the instructions and familiarize yourself with all the operational aspects of your new heater.

  • Page 3: Specifications

    17. Use only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by unauthorized dealers may cause hazards.

  • Page 4: Product Diagram

    WARNING: This heater has a voltage rating of 120 volts. The cord has a plug as shown in A. An adapter as shown in C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box.
  • Page 5 Control Panel 1. Timer button: User setting timing boot or shutdown . 2. Flame light button: Adjust the brightness of the flame . 3. Heater button: Set up the heater mode and turn off the heat. 4. Power indication light: After electrifying show red, press the power button to display the red light and flame open.
  • Page 6 Remote Control Power button: Powers the display on and off Up button: For setting temperature or time upward Down button：For setting temperature or time downward Flame light button: Adjust the brightness of the flame Heater button: Set up the heater mode and turn off Timer button: User setting timing boot or shutdown PREPARATION Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet.
  • Page 7 Power for heat-up mode is 1500W; heat-down is 750W,and turn off the heat. 2、Setting Desired Temperature Adjust the desired temperature by pressing the Up/Down arrows on the con trol panel or remote control. Desired temperature options vary from 59℉ to 95℉. Once you have chosen the desired temperature, the heater will remain on until the room temperature increases to the temperature on the digital display.

  • Page 8: Maintenance

    5、Setting the POWER-ON-TIMER Function (Note: The Power-ON-Timer Function will allow for the heater to power ON after a certain set time, and can only be set while the heater’s display is in the “Off” position. Turn the heater to the “OFF” position .Press the Timer button on the heater’s control panel or the remote.
  • Page 9 5. DO NOT immerse the heater in water. 6. Wait until the unit is completely dry before use. 7. Air filter needs cleaning after used 3 months of use. Please take off the filter with the 2 steps in the drawing below. Flush and clean the filter with water, Then, dry it out and re- assemble.

  • Page 10: Basic Troubleshooting

    BASIC TROUBLESHOOTING If the heater will not operate, please check the following before seeking repair advice: 1. Check if the power cord is plugged into an electrical outlet, if not, plug in. 2. Check if electricity to the main power switch (in the back) is working. 3.

Table of Contents