SAFETY PROCEDURES Your new SEM 0100 Sledgehammer delivers a staggering 6,000 pounds of force to a conical punch causing catastrophic trauma to the hard drive chassis while destroying the internal platter, serious and permanent injury may result if proper precautions are not followed.
PARTS LIST Reference Figure A NUMBER PART NUMBER DESCRIPTION 600HDD0100 Press 850HDCANVIL Anvil MC91074A136 Anvil Lock Washer 851MCHANDLE Handle (Long) 8519753K82 Handle End Cap 851MCHANDLES Handle (Short) 8519753K2A Handle End Cap M10 Set Screw 5mm Hex L-Key 3/8-16 x 4” Bolts 3/8 x 2”...
Should the packaging have been discarded before the (30) day requested period, packaging costs will be incurred by the customer. 1) Place the 0100 Sledgehammer on a strong and sturdy surface. Such as a work table or SEM’s Optional Heavy Duty Stand.
Page 7
IMPORTANT: Long handle MUST be used when crushing hard drives. Warning: While operating the model 0100 Sledgehammer pieces of material can eject. See your internal safety officer and ask about your PPE for area of operation. We recommend wearing safety glasses.
CHANGE SETTINGS and MAINTENANCE Change angle of handle 1) Remove Handle Tool required: 5 mm Hex L-Key 2) Loosen set screw on shaft collar than remove. Tool required: M6 Alan Wrench For NATIONWIDE SERVICE CALL 1(800)225-9293...
Page 9
CHANGE SETTINGS and MAINTENANCE Cont….. 3) Pull shaft out until the teeth are no longer engaged. 4) Lift anvil to desired height. 5) Once desired height is reached, lock down the center bolts with the jam nuts on them. Tool required: 5/8 Wrench Center bolts with jam nuts For NATIONWIDE SERVICE CALL 1(800)225-9293...
Page 10
CHANGE SETTINGS and MAINTENANCE Cont….. 6) Turn shaft until the hole for the handle is approximately set at 45°, and then push back in. Note: Once handle insert hole is set at approximately 45°, you may have to slightly twist the shaft to align teeth to slide shaft back into place.
Page 11
CHANGE SETTINGS and MAINTENANCE Cont….. Replacing or Removing the Anvil 1) Lift handle so anvil is clear of any obstructions. 2) Lock down the center bolts with the jam nuts on them. Tool required: 5/8 Wrench 3) Remove anvil Tool required: Large Adjustable Wrench Note: Do not lose the lock washer on the top of the anvil, as this must be put back on anvil.
Page 12
CHANGE SETTINGS and MAINTENANCE Cont….. Remove or Replace Coupling 1) Lift handle so anvil is clear of any obstructions. 2) Lock down the center bolts with the jam nuts on them. Tool required: 5/8 Wrench For NATIONWIDE SERVICE CALL 1(800)225-9293...
OPERATION Punching Hard Drives Warning: Unit is shipped ready to destroy 1” hard drives, you may want to reset if punching 1.65” hard drives (refer to the Changing Settings and Maintenance on page 5) 1) Lift handle to insert hard drive. Note: It is recommended to punch the hard drives on the PC board side.
Page 14
OPERATION Cont… Note: Anvil will not penetrate thru the entire hard drive. The model 0100 Sledgehammer pierces and deforms hard drive to disable the drive. 3) Pull or push handle up to remove hard drive. If more deformation is needed turn hard drive 180° to penetrate opposite side.
Page 15
OPERATION Cont… Punching DLT tapes 1) Lift handle to insert DLT tape. Note: It is recommended to punch the top side in the center of tape. 2) Pull or push handle down to penetrate DLT tape. Warning: DLT tape is not considered destroyed. Only the metal is removed to make the tape inoperable. For NATIONWIDE SERVICE CALL 1(800)225-9293...
PRODUCT SPECIFICATION Drive Types Personal Computer and/or Notebook style Hard Disk Drives regardless of their size, format or type from .65” to 1.6” thickness Destruction Time 5 second full cycle….can also destroy up to 2 notebook drives in one 5 second cycle. Dimensions / Weight 8”...