Amped Wireless AP20000G Setup Manual

SETUP GUIDE
High Power Wireless-N 600mW Gigabit Dual Band Access Point
1
Connect the Access Point to your Router/Network
a
2
Connect your Computer to the Access Point

Wireless Connections:

Scan for available wireless networks on your
PC and connect to one of the following networks:
NETWORK ID:
NETWORK ID:
!
The instructions below are optional. You may now use your Access Point without any additional
configurations. However, if you wish to change any settings (such as network ID and security) for the
Access Point, follow the instructions below to access the configuration menu of the Access Point.
Note: If your network uses static IP address assignments, you will need to manually configure the settings for your
Access Point. See the instructions on the back to access the configuration menu of the Access Point.
1
Optional Configurations: Accessing the Dashboard / Web Menu
Connect to the Access Point using a network cable or scan for available wireless networks on your PC
and connect to:
NETWORK ID:
PASSWORD:
Amped_AP_2.4GHz
2 Open your Web Browser
3

Welcome to the Dashboard

4
Set the System Clock Time
5
Configure your Wireless Settings
7

Setup Summary

— R E A D
b
Router
(LAN port)
Modem Internet
c
Connect to your
router/switch
Amped_AP_2.4GHz
wireless
PASSWORD:
- or -
Amped_AP_5.0GHz
wireless
PASSWORD:
Congratulations, you're done!
Amped_AP_2.4GHz
wireless
30
F I R S T
Attach the Antennas
Plug in the Power Adapter
Connect the Access Point to your
Router's Network (LAN) port, or a Network
network switch
Allow up to three (3) minutes for the
Access Point to automatically configure
itself to your network
Wired Connections:
Attach any Wired Devices
Access Point using an Ethernet
cable.
NETWORK ID:
- or -
PASSWORD:
Amped_AP_5.0GHz
Enter the setup web address into your browser:
http://setup.ampedwireless.com
If the URL fails to open, then try: http://192.168.80.240
The Dashboard provides you with a quick
glance at your system status.
Click on
System Clock
1
Wireless Network SSID
2
Wireless Network Security Key
3
The System Clock is used for system logs
and setting schedules for Internet access.
Click Sync
with the time on your computer.
Click Next
The Access Point creates two Wi-Fi networks:
a 2.4GHz Wi-Fi network and a 5.0GHz Wi-Fi
network.
The IDs of your Wi-Fi networks are:
Amped_AP_2.4GHz
To change them, enter a new name in the SSID field.
Users connecting wirelessly to the Access Point will
use this ID to identify your Wi-Fi network.
The default Security Key (WPA/WPA2 Mixed
Mode) for both (2.4GHz and 5.0GHz) networks
wireless
is:
To change it, enter a new key in the Security Key
field. The key must be at least 8 characters long.
Click Next
Point will reboot.
The web menu will now apply your settings.
This process may take up to 90 seconds.
Do not refresh the web page. The page will
automatically reload with the summary.
If you are connected wirelessly to the Access
Point, you will need to reconnect after the
Access Point reboots.
The Setup Summary provides you with
information regarding your current settings.
If you have additional wired or wireless
devices you may connect them at this time.
?
Phone: 888-573-8820
Email: techsupport@ampedwireless.com
Web: www.ampedwireless.com/support
If you have any problems during the installation process,
please contact Amped Wireless Elite Support for further assistance.
?
Need Help? Give us a call.
Phone: 888-573-8820
Email: techsupport@ampedwireless.com
Web: www.ampedwireless.com/support
—
AP20000G
to the
Amped_AP_5.0GHz
wireless
Basic Setup to configure:
to synchronize the System Clock
to continue.
Amped_AP_5.0GHz
and
to apply your settings. The Access
Need Help? Give us a call.
v072612