Advertisement
WARNING
Electrical Shock Hazard
Disconnect power before making
electrical connections.
Connect ground wire to green ground
screw in terminal box.
Failure to do so can result in death or
electrical shock.
to light
ground
bulbs
wires
power
white wires
supply
wiring
18a.
For models requiring direct wiring:
Connect white wiring from the terminal box,
light harness and power supply wiring
together with twist-on connector.
Connect black wiring from the terminal box
to power supply wiring with twist-on
connector.
Connect the power supply ground wire and
the green ground wire inside the terminal
box under the terminal box ground screw.
Use caulking to seal wire opening.
Replace terminal box cover.
For cord connected models:
WARNING
Electrical Shock Hazard
Plug into a grounded 3-prong outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these instructions can
result in death, fire, or electrical shock.
For your personal safety, this range hood
must be grounded. To minimize possible
shock hazard, the cord must be plugged
into a mating, 3-prong, ground-type outlet,
grounded in accordance with National
Electrical Code, ANSI/NFPA 70 – latest
edition* and all local codes and
ordinances.
If mating outlet is not available, it is the
responsibility and obligation of the
customer to have a properly grounded, 3-
prong outlet installed by a qualified
electrician.
Do not use an extension cord.
Using a U.L.-listed power supply
cord-connection kit:
Follow Power Cord Kit instructions for
connecting wiring.
Replace terminal box cover.
19a.
Turn power supply on.
Copies of standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Panel E
Use & Care
Information
Use this range hood only in the manner
intended by the manufacturer. If you have
any questions, contact the manufacturer.
Before installation and before servicing or
cleaning range hood, switch off power at
service panel and lock service panel to
prevent power from being switched on
accidentally. When the service
disconnecting means cannot be locked,
securely fasten a prominent warning
device, such as a tag, to the service panel.
Operation of
range hood
For best results, turn range hood fan on at
beginning of cooking and allow it to run
until all smoke and odors are removed from
room.
terminal
To adjust fan speed:
box
Turn fan speed control to desired setting
connector
between "Hi" and "Lo". Speed may be
blower
wiring
changed anytime during range hood
connector
operation.
black wires
To turn range hood light "ON" and "OFF":
Turn light control to operate light "ON" or
"OFF". Light may be turned to "OFF" or
"ON" anytime during range hood
twist-on
operation.
connectors
"Night" light setting:
Turn light control to "Night" setting when
you need the light dimmed for use as a
night light.
Care of range hood
Filters:
For best results, remove and clean often.
holes
filters
To remove aluminum filters:
Place finger in hole. Pull back and down.
To clean aluminum filters:
Place filters in dishwasher or hot sudsy water
to clean.
To reinstall aluminum filters:
Place edge of filter in channel opening so
that side is above flange. Pull back. Press
filter into position.
When it's time to replace your
aluminum filter:
1. Choose your filter order number.
30" Hood Model RH8330:
Order Filter no. 883276
36" Hood Model RH8336:
Order Filter no. 883277
2. Call Whirlpool's Telesales line at
1-800-442-9991
3. Give the Telesales Representative the
part number needed.
4. The Representative will give you the
current price.
5. Place your order using your Master
Card
®
, Visa
®
or Discover
®
6. If you wish: mail a check or money order
to:
Whirlpool Corporation
1900 Whirlpool Drive
LaPorte, IN 46350-9980
Attn: Accessory Accounting
7. Be sure to ask the Telesales
Representative about the wide variety of
other Whirlpool Product Accessories.
Blower motor:
To clean blower motor:
Clean exterior of motor with a damp cloth
and grease-cutting detergent.
Exterior surfaces:
Clean the range hood with a mild
detergent and soft cloth. Do Not use
abrasive cleaners or steel wool.
Light:
Do Not use bulbs larger than 60 watts
in light sockets.
To replace bulbs:
Remove three screws that hold light cover
panel in place. Remove panel and set
aside. Replace bulb.
Replace light cover panel before operating
fan or light.
Light bulbs are not included.
credit card.
Advertisement
