Zenith P50W38 Installation And Operating Manual page 26

External Control Device Setup
Set ID
Set ID
- Use this function to specify a monitor ID number.
- Refer to 'Real Data Mapping 1'. See page 27.
1. Press the MENU button and then use the
2. Press the G button and then use
G
3. Press the button and then use
monitor ID number.
• The adjustment range of Set ID. is 1 ~ 99.
Communication Parameters
Communication Parameters
• Baud rate : 115200 bps (UART)
• Data length : 8 bits
• Parity : None
Command Reference List
Command Reference List
COMMAND 1 COMMAND 2
01. Power
02. Input Select
03. Aspect Ratio
04. Screen Mute
05. Volume Mute
06. Volume Control
07. Contrast
08. Brightness
09. Color
10. Tint
11. Sharpness
12. OSD Select
13. Remote Control Lock Mode k
14. PIP/Twin
15. PIP Aspect Ratio
16. Split Zoom
17. PIP Position
18. Treble
19. Bass
20. Balance
21. Color Temperature
22. Red Adjustment
23. Green Adjustment
24. Blue Adjustment
25. PIP Input Source
26. Abnormal State
27. ISM Method
28. Low Power
29. Orbiter Time Setting
30. Orbiter Pixel Setting
31. Picture Size Setting
for Twin Picture mode
32. Auto Configure
•
Menu doesn't display on screen when setting the 4,
12, 13, and 26 ~ 32.
26 Plasma Display Panel
button to select the SPECIAL menu.
D / E
button to select Set ID..
D / E
F / G button to adjust Set ID. to choose the desired
DATA
(Hexadecimal)
k a 0 ~ 1
k b 0 ~ 4
k c 0 ~ 3
k d 0 ~ 1
k e 0 ~ 1
k f 0 ~ 64
k g 0 ~ 64
k h 0 ~ 64
k i 0 ~ 64
k j 0 ~ 64
k k 0 ~ 64
k l 0 ~ 1
m 0 ~ 1
k n 0 ~ 3
k o 0 ~ 1
k p 21 ~99
k q 0 ~ 3
k r 0 ~ 64
k s 0 ~ 64
k t 0 ~ 64
k u 0 ~ 3
k v 0 ~ C8
k w 0 ~ C8
k $ 0 ~ C8
k y 0 ~ 4
k z 0 ~ a
j p 0 ~ 3
j q 0 ~ 1
j r 1 ~ FE
j s 0 ~9
j t 0 ~64
j u 1
• Stop bit : 1 bit
• Communication code : ASCII code
T ransmission / Receiving Protocol
T ransmission / Receiving Protocol
Transmission
[Command1][Command2][ ][Set ID][ ][Data][Cr]
* [Command 1]: k, j
* [Command 2]: To control PDP set.
* [Set ID]: You can adjust the set ID to choose desired moni-
tor ID number in Special menu. Adjustment range
is 1 ~ 99. When selecting Set ID '0', every con-
nected PDP set is controlled. Set ID is indicated
as decimal (1~99) on menu and as Hexa decimal
(0x0~0x63) on transmission/receiving protocol.
* [DATA]: To transmit command data.
Transmit 'FF' data to read status of command.
* [Cr]: Carriage Return
ASCII code '0x0D'
* [ ]: ASCII code 'space (0x20)'
OK Acknowledgement
[Command2][ ][Set ID][ ][OK][Data][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving normal data. At this time, if the
data is data read mode, it indicates present status data. If
the data is data write mode, it returns the data of the PC
computer.
Error Acknowledgement
[Command2][ ][Set ID][ ][NG][x]
* The Monitor transmits ACK (acknowledgement) based on
this format when receiving abnormal data from
non-viable functions or communication errors.
Data 1: Illegal Code
2: Not supported function
3: Wait more time
VIDEO
Language
AUDIO
Key lock
ISM Method
TIME
Low power
Set ID. G 1
SPECIAL
OSD Rotate
SCREEN
TWIN
MENU Prev.