Maytag Stacked Washer/Dryer Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Maytag Manuals
  4. Washer/Dryer
  5. Stacked Washer/Dryer
  6. Installation instructions manual
Maytag Stacked Washer/Dryer Installation Instructions Manual

Maytag Stacked Washer/Dryer Installation Instructions Manual

Maytag stacked washer/dryer installation instructions
Hide thumbs Also See for Stacked Washer/Dryer:
Table of Contents

Advertisement

Quick Links

See also: Instruction and Installation Manual
INSTALLATION INSTRUCTIONS
LEAVE THESE INSTRUCTIONS WITH THE OWNER
IMPORTANT TO INSTALLER
REMOVE THE DOOR FROM ALL DISCARDED
APPLIANCES SUCH AS DRYERS AND
COMBINATION WASHER/DRYERS TO AVOID
THE DANGER OF A CHILD SUFFOCATING
SHOULD HE/SHE CRAWL INSIDE AND THE
DOOR BE SHUT.
THE APPLIANCE MUST NOT BE INSTALLED
OR STORED IN AN AREA WHERE IT WILL BE
EXPOSED TO WATER AND/OR WEATHER.
U.S. MODELS
PLEASE READ THE FOLLOWING INSTRUC-
TIONS CAREFULLY BEFORE STARTING TO
INSTALL THE DRYER. FOR GAS DRYERS,
THE INSTALLATION MUST CONFORM WITH
THE NATIONAL FUEL GAS CODE ANSI
Z223.1, LATEST REVISION. ANY QUESTIONS
CONCERNING THIS SHOULD BE REFERRED
TO THE LOCAL GAS UTILITY.
STACKED WASHER-DRYER
printed in U.S.A.
CANADIAN MODELS
PLEASE READ THE FOLLOWING INSTRUC-
TIONS CAREFULLY BEFORE STARTING TO
INSTALL THE DRYER.
INSTALLATION,
REFER
CAN/CGA B149 (.1 OR .2) INSTALLATION
CODE.
ANY QUESTIONS SHOULD BE
REFERRED TO THE LOCAL GAS UTILITY.
This folder contains information of interest to the
owner. After the appliance has been properly
installed, LEAVE THESE INSTRUCTIONS
WITH THE OWNER.
NOTICE:
SERVICE CALLS PERFORMED
AS A RESULT OF POOR
INSTALLATION ARE THE
RESPONSIBILITY OF THE
INSTALLER.
FOR GAS DRYER
TO
STANDARD
6 3717020

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stacked Washer/Dryer and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Maytag Stacked Washer/Dryer

Summary of Contents for Maytag Stacked Washer/Dryer

  • Page 1 STACKED WASHER-DRYER INSTALLATION INSTRUCTIONS LEAVE THESE INSTRUCTIONS WITH THE OWNER IMPORTANT TO INSTALLER REMOVE THE DOOR FROM ALL DISCARDED APPLIANCES SUCH AS DRYERS AND COMBINATION WASHER/DRYERS TO AVOID THE DANGER OF A CHILD SUFFOCATING SHOULD HE/SHE CRAWL INSIDE AND THE DOOR BE SHUT.

  • Page 2: Uncrating

    IMPORTANT TO OWNER Retain these instructions for future reference. This new Maytag appliance is designed to serve you dependably for many years. However, it cannot do so unless provided with sufficient electrical power, suitable exhausting and if a gas model, adequate gas supply. We urge you to read this carefully to make sure all requirements are met.

  • Page 3: Pre-Installation Considerations

    PREINSTALLATION CONSIDERATIONS Location: The stacked washer/dryer is approved for zero clearance installation on the sides and the back (depending on venting used). The loca- tion selected must take into consideration the dimensions of the unit and convenience for cus- tomer use and access in case service should be needed.

  • Page 4: Alcove Or Closet Installation

    ALCOVE OR CLOSET INSTALLATION When the stacked washer/dryer is to be installed in an alcove area or a closet, clearance should be provided around the unit for an adequate air supply and for ease of installation and servicing. An appliance installed in a closet shall have no...

  • Page 5: Direct Exhaust

    When located in a bedroom, bathroom or closet, the dryer must be exhausted to the outside. The stacked washer/dryer can only be exhaust- ed out the back. A 4 inch vent should be installed to accept the exhaust from the dryer.

  • Page 6: Rigid Ductwork Limitations

    RIGID DUCTWORK LIMITATIONS Rigid metal ductwork should not exceed 54 feet of straight 4 inch duct. Each 90° elbow and the exhaust hood should be considered equivalent to 8 feet of straight ductwork. For example, if an exhaust hood and two 90° elbows are used, the maximum straight duct allowed would be 26 feet.
  • Page 7 Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. ADDITIONAL GROUND PROCEDURE WHERE LOCAL CODE PERMITS. A grounding kit (Part No. 12001875) is available. It contains the external ground wire, clamp, ground screw and washer.

  • Page 8: 4-Wire Receptacle/System Connections

    4. Connect the other two wires of the cord to the outer terminals of the terminal block. 5. Replace the terminal block cover. 208 VOLT OPERATION A stacked washer/dryer model is available for Four-Wire Receptacle 208 volt operation. Canadian Models All Canadian models are shipped with the power cord attached.

  • Page 9: Gas Connection

    The use of a laundry built-in wall box can greatly simplify installation. If the faucets and/or drain is located to either side of the stacked washer/dryer, openings are located in the dryer stand uprights to allow hoses and power cords to be passed through.

  • Page 10: Install Dryer Unit And Stand

    INSTALL DRYER UNIT AND STAND The dryer and stand are installed first. With the connections prepared for exhausting, electric power and gas (if gas stacked washer/dryer, see page 9), the dryer and stand are moved to the location. NOTE: When moving the dryer and stand on an appliance hand truck, it is recommended that the dryer and stand be trucked upside down.

  • Page 11: Install Washer Unit

    DRYER INSTALLATION ACCESSORIES Vent Kit – standard – 4″ (10.16cm) kit includes two elbows, three pipes and one vent hood Vent Hood – 4″ (10.16cm) opening Aluminum Pipe – 4″ x 24″ (10.16cm x 60.96cm) Aluminum Elbow – 4″ (10.16cm) Aluminum Window Plate –...
  • Page 12 Attach the inlet hoses to the HOT and COLD faucets. Being sure the hose marked “HOT” is attached to the HOT water faucet. Tighten by hand until snug and then 2/3 of a turn with pliers. Do not overtighten. Attach the 90° ends of the inlet hoses to the HOT and COLD connections on the...
  • Page 13 Connect the dryer power cord to 120 volt AC outlet for gas models. 240 volt outlet for electric models. Make appropriate external ground connection. See DETAILED Installation Instructions for ELECTRICAL REQUIRE- MENTS AND GROUNDING (pages 6-7). Slide washer all the way back into stand. Tabs on stand legs are to slide into the washer front panel.

  • Page 14: Replacement Parts

    Aerosol pretreated products can also damage finish on control panel. When using these products on garments placed in the stacked washer/dryer, it is advisable to avoid control panel area with the overspray. WATER DAMAGE FROM FLOODING In the event the stacked washer/dryer is exposed to water from flooding, call your local Maytag dealer before using.

Table of Contents