Hilti TE 3000-AVR Original Operating Instructions
Hide thumbs
Also See for TE 3000-AVR:
- Operating instructions manual (250 pages) ,
- Manual (212 pages) ,
- Original operating instructions (200 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Instruction Manual
Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02
TE 3000-AVR
Bedienungsanleitung
Operating instructions
Mode d'emploi
Istruzioni d'uso
Manual de instrucciones
Manual de instruções
Gebruiksaanwijzing
Brugsanvisning
Bruksanvisning
Bruksanvisning
Käyttöohje
Lietošanas pamācība
Instrukcija
Kasutusjuhend
de
en
fr
it
es
pt
nl
da
sv
no
fi
lv
lt
et
Advertisement
Table of Contents
Related Manuals for Hilti TE 3000-AVR
Summary of Contents for Hilti TE 3000-AVR
- Page 1 TE 3000-AVR Bedienungsanleitung Operating instructions Mode d’emploi Istruzioni d’uso Manual de instrucciones Manual de instruções Gebruiksaanwijzing Brugsanvisning Bruksanvisning Bruksanvisning Käyttöohje Lietošanas pamācība Instrukcija Kasutusjuhend Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02...
-
Page 2: Product View
Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02... - Page 3 Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02...
- Page 4 Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02...
- Page 5 Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02...
- Page 6 TE-H28P SM 400 mm 500 mm TE-H28P FM 400 mm 500 mm TE-H28P SPM 80/400 mm 80/500 mm TE-H28P SPMA 125/450 mm TE-H28P SPI 500 mm TE-H28 400 mm TE STP 150 x 150 mm 200 x 200 mm Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02...
-
Page 7: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS TE 3000‑AVR breaker 1 These numbers refer to the corresponding illustra- It is essential that the operating instructions tions. The illustrations can be found on the fold-out cover are read before the power tool is operated for pages. -
Page 8: Description
The power tool may be operated only when connected to a power supply providing a voltage and frequency in compliance with the information given on its type identification plate. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. - Page 9 Observe the information printed in the operating instructions concerning operation, care and maintenance. Modification of the power tool or tampering with its parts is not permissible. 2.2 Chuck 28 mm hex. chuck 2.3 Switch On / off switch 2.4 Grips Grips incorporating AVR Active Vibration Reduction 2.5 Lubrication Permanent lubrication with separate lubrication chambers for the gearing and hammering mechanism.
-
Page 10: Accessories, Consumables
TPS Theft Protection System with Company Card, Company Remote and TPS‑K key (optional) Use the Hilti chisels or other tools listed below. With these you will achieve higher performance and longer lifetime as the power tool and chisels have been optimized as a system. -
Page 11: Safety Instructions
Noise and vibration information (measured in accordance with EN 60745‑1): Typical A-weighted sound power level, TE 3000-AVR 105 dB (A) Typical A-weighted emission sound pressure level, TE... - Page 12 c) Keep children and bystanders away while operat- are connected and properly used. Use of dust ing a power tool. Distractions can cause you to lose collection can reduce dust-related hazards. control. 5.1.4 Power tool use and care 5.1.2 Electrical safety a) Do not force the power tool.
- Page 13 Children must be instructed not to play with the should be checked at regular intervals at a Hilti power tool. Service Center. Under unfavorable circumstances, dampness or dust adhering to the surface of...
-
Page 14: Before Use
6 Before use 6.3 Transport CAUTION Use the transport trolley or other means of convey- ance whenever possible. The power tool should always be carried by two persons if no transport trolley or means CAUTION of conveyance is available for use. Be aware that the The power tool must be disconnected from the elec- power tool plus transport trolley present a considerable tric supply. - Page 15 7.1.2 Removing the chisel 7.2.1 TPS Theft Protection System (optional) DANGER NOTE Do not lay a hot insert tool down on flammable ma- The power tool may be equipped with the optional theft terials. This could cause the material to ignite, resulting protection system.
-
Page 16: Care And Maintenance
Sections of the grip are made from a CAUTION synthetic rubber material. The power tool must always be checked by a Hilti Never operate the power tool when the ventilation slots specialist for internal or external damage whenever it are blocked. -
Page 17: Disposal
NOTE If the fault cannot be eliminated by the measures listed above, have the power tool checked by Hilti Service. 10 Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. -
Page 18: Ec Declaration Of Conformity (Original)
Authorized assessment office (0044) TÜV NORD CERT GmbH Hannover office Am TÜV 1 30519 Hannover Germany Hilti Corporation, Feldkircherstrasse 100, FL‑9494 Schaan Paolo Luccini Jan Doongaji Head of BA Quality and Process Management Executive Vice President Business Area Electric Tools & Accessories Business Unit Power Tools &... - Page 19 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3750 | 0513 | 00-Pos. 1 | 1 Printed in Liechtenstein © 2013 Right of technical and programme changes reserved S. E. & O 426346 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5070890 / 000 / 02...