Ec Declaration Of Conformity - Flymo Sabre Trim Original Instructions Manual

If any part is found to be defective due to faulty manufacture within
the guarantee period, Husqvarna UK Ltd., through its Authorised
Service Repairers will effect the repair or replacement to the cus-
tomer free of charge providing:
(a) The fault is reported directly to the Authorised Repairer.
(b) Proof of purchase is provided.
(c) The fault is not caused by misuse, neglect or faulty adjust-
ment by the user.
(d) The failure has not occurred through fair wear and tear.
(e) The machine has not been serviced or repaired, taken apart
or tampered with by any person not authorised by Husqvarna
UK Ltd..
(f) The machine has not been used for hire.
(g) The machine is owned by the original purchaser.
(h) The machine has not been used outside of the country for
which it was specified.
(i) The machine has not been used commercially.
* This guarantee is additional to, and in no way diminishes the
customers statutory rights.
Husqvarna AB, 561 82, Huskvarna, Sweden
Declare under our sole responsibility that the product(s);
Category........................................ Battery Lawn Trimmer
Model(s)......................................... GTC24A
Identification of Series................... See Product Rating Label
Year of Construction...................... See Product Rating Label
Complies with the essential requirements & provisions of the following EC Directives:
2006/42/EC, 2004/108/EC, 2000/14/EC
based on the following EU harmonised standards applied:
EN60335-1, EN60335-2-91, EN786, EN60335-2-29, EN50366, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-3
The maximum A weighted sound pressure level L
uct(s) corresponds to the Level given in the table.
The maximum hand / arm vibration weighted value measured according to EN ISO 5349 on a sample of the above
product(s) corresponds to the Value
2000/14/EC: The Measured Sound Power L
figures.
Conformity Assessment Procedure.................. Annex VI
Notified Body.................................................... Intertek, Cleeve Road
Newton Aycliffe, 11/06/2010
M. Bowden,
Global R & D Director - Walk behind
Husqvarna UK Ltd.
Keeper of Technical documentation
Our policy of continuous improvement means that the specification of products may be altered from time to time without prior notice.
Copyright © 2010 Flymo S.A. All rights reserved. Flymo® and other product and feature names are registered or unregistered trademarks
5100449-02
Guarantee & Guarantee Policy

EC Declaration of Conformity

at the operator's position, recorded on a sample of the above prod-
pA
a h
given in the table.
& Guaranteed Sound Power L
WA
Leatherhead, Surrey
KT22 7SB, England
Type
Width of Cut (cm)
Speed of Rotation of Cutting Device (RPM)
Measured Sound Power LWA (dB(A))
Guaranteed Sound Power LWA (dB(A))
Level (dB(A))
Uncertainty (dB(A))
Value a h (m/s 2 )
Uncertainty K of a h (m/s2)
Weight (Kg)
Husqvarna AB
Huskvarna
Failures due to the following are not covered, therefore it is important that
you read the instructions contained in this Operator's Manual and under-
stand how to operate and maintain your machine:
Failures not covered by guarantee
* Replacing Nylon Line.
* Failures as a result of not reporting an initial fault.
* Failures as a result of sudden impact.
* Failures as a result of not using the product in accordance with
the instructions and recommendations contained in this Opera-
tor's Manual.
* Machines used for hire are not covered by this guarantee.
* The following items listed are considered as wearing parts and their life
is dependent on regular maintenance and are, therefore not normally
subject to a valid warranty claim: Nylon Line., Spool & Line
* Caution!
Husqvarna UK Ltd. does not accept liability under the warranty for
defects caused in whole or part, directly or indirectly by the fitting of
replacement parts or additional parts that are not either manufac-
tured or approved by Husqvarna UK Ltd., or by the machine having
been modified in any way.
WA
561 82
Sweden
of Flymo S.A.
values are according to the tabulated
GCT24A
25
10,000
89
93
75.6
2.5
1.87
1.5
6.89