PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any inaccuracies or omissions that may have occurred.
Page 3
Do not dispose of WEEE as unsorted municipal waste and have to collect such WEEE separately. Revision PLANET Industrial 10/100/1000BASE-T to 1/2 100/1000BASE-X SFP Media Converter User's Manual FOR MODELS: IGT-805AT / IGT-1205AT REVISION: 1.0 (MARCH, 2015)
1.2 Product Overview Flexibility and Network Distance Extension Solution The IGT-805AT / IGT-1205AT Industrial Gigabit Media Converter is equipped with one 10/100/1000BASE-T auto-negotiation port and one / two 100/1000X SFP slots. The SFP slots are compatible with 1000BASE-X or 100BASE-FX through SFP (Small Form Factor Pluggable) fiber-optic transceiver.
Gigabit environments. With a 4/6Gbps internal fabric and featuring auto negotiation support in its Gigabit port, the IGT-805AT / IGT-1205AT Industrial Gigabit Media Converter can handle large amounts of data in a secure topology linking to a backbone or high capacity servers.
Page 8
IGT-1205AT Physical Port 1-port 10/100/1000BASE-T RJ45 with auto MDI / MDI-X function 2 SFP interfaces, 100/1000BASE-X dual mode (DIP switch control) Layer 2 Features IEEE 802.3 / 802.3u / 802.3ab / 802.3z Ethernet standard compliant Supports auto-negotiation and 10/100Mbps half / full duplex and 1000Mbps full duplex mode ...
2. Hardware Description 2.1 Physical Dimensions IGT-805AT dimensions (W x D x H): 32 x 87 x 135mm Side View Front View...
Page 12
IGT-1205AT dimensions (W x D x H): 32 x 87 x 135mm Side View PWR1 Fault PWR2 Port 1 Port 2 Mode 100FX 1000X 100FX 1000X Redundant Switch Front View...
Figures 2-1 and 2-2 show the front panels of the Industrial Gigabit Media Converter. P2 FAULT P2 FAULT 1000X LNK / 1000X 100/1000X LNK/ACT LNK / 10/100/1000T 10/100/1000T LNK/ACT 1000 LNK/ACT LNK/ACT 1000 IGT-805AT IGT-1205AT Figure 2-1: IGT-805AT Front Panel Figure 2-2: IGT-1205AT Front Panel...
Lit: indicates power 2 has power. Green Lit: indicates either power 1 or power 2 has no FAULT Green power. Per 10/100/1000BASE-T Port (IGT-805AT) Color Function Lit: indicates that the Gigabit Ethernet Port is successfully connecting to the network at 10/100/1000Mbps.
Page 15
Per 10/100/1000BASE-T Port (IGT-1205AT) Color Function Lit: indicates the link through that port is successfully established at 100Mbps or 10Mbps. Blinking: indicate that the Switch is actively Orange LNK/ACT sending or receiving data over that port. Off: indicates the link through that port is successfully established at 1000Mbps.
2.4 Converter Upper Panel The upper panel of the IGT-805AT and IGT-1205AT consist of one terminal block connector within two DC power inputs, and the IGT-1205AT also provides 3 DIP Switches for 100/1000X fiber support on two SFP slots and fiber redundant function. Figure 2-3 shows the...
3. INSTALLATION This section describes the functionalities of the Industrial Gigabit Media Converter’s components and guides you to how to install it on the desktop. Basic knowledge of networking is assumed. Please read this chapter completely before continuing. 3.1 Quick Installation Steps Step 1: Unpack the Industrial Gigabit Media Converter.
Manual uses IGS-801 (PLANET 8-port Industrial Gigabit Switch) as the example. However, the steps for PLANET Industrial Note Switch and Industrial Media Converter are similar. 3.2.1 DIN-rail Mounting The DIN-rail is screwed on the Industrial Gigabit Media Converter when is out of factory.
Page 19
Step 2: Lightly insert the DIN-rail into the track. Step 3: Make sure the DIN-rail is tightly secured on the track. Step 4: Please refer to the following procedures to remove the Industrial Gigabit Media Converter from the track.
Step 5: Lightly pull out the bottom of the DIN-Rail from the track to remove. 3.2.2 Wall-mount Plate Mounting To install the Industrial Gigabit Media Converter on the wall, please follow the instructions described below. Step 1: Remove the DIN-Rail from the Industrial Gigabit Media Converter;...
1 2 3 4 5 6 The above top panel is based on IGT-1205AT. The 6-contact terminal block connector is the same as that of IGT-805AT. But the IGT-805AT does not provide 3 DIP Note switches. 2. Tighten the wire-clamp screws for preventing the wires from loos- ening.
The wire gauge for the terminal block should be in the range between 12 and 24 AWG. Note 3.4 Wiring the Fault Alarm Contact The fault alarm contacts are in the middle of the terminal block connector as the picture shows below. When inserting the wires, the Industrial Gigabit Media Converter will detect the fault status of the power failure and then forms an open circuit.
MGB / MFB Series Transceiver Figure 3-1: Plug in the SFP Transceiver It is recommended to use PLANET SFPs on the Indus- trial Gigabit Media Converter. If you insert an SFP trans- ceiver that is not supported, the Industrial Gigabit Media Note Converter will not recognize it.
Page 24
2. Make sure both sides of the SFP transceiver are with the same media type; example, 1000BASE-SX 1000BASE-SX, 1000BASE-LX to 1000BASE-LX. 3. Check whether the fiber-optic cable type matches the SFP trans- ceiver model. To connect to 1000BASE-SX SFP transceiver, use the multi-mode fiber cable with one side being the male duplex LC connector type.
Page 25
Connecting the fiber cable 1. Attach the duplex LC connector on the network cable to the SFP transceiver. 2. Connect the other end of the cable to a device, switches with SFP installed, to fiber NIC on a workstation or a Media Converter. 3.
Page 26
10/100/1000BASE-T The 10/100/1000BASE-T port comes with auto-negotiation capability. It automatically supports 1000BASE-T, 100BASE-TX and 10BASE-T networks. Users only need to plug a working network device into the 10/100/1000BASE-T port, and then turn on the Industrial Gigabit Media Converter. The port will automatically runs in 10Mbps, 20Mbps, 100Mbps or 200Mbps and 1000Mbps or 2000Mbps after the negotiation with the connected device.
3.6 Redundancy Overview (IGT-1205AT only) The IGT-1205AT provides rapid fiber redundancy of link for highly critical Ethernet applications. The redundant-mode supports auto- recover function. If the destination port of a packet is link down, it will forward the packet to the other port of the backup pair. The following figure shows the redundant function.
4. Applications In this paragraph, we will describe how to install the Industrial Gigabit Media Converter. Transportation Networking Control Center Serial over IGT-1205AT Ethernet Device IGT-805AT 20km IGT-805AT Outdoor IP Camera Robot 50km 1000 1000 IGT-1205AT 120km Robot Subway 2...
5. Troubleshooting This chapter contains information to help you solve issues. If the Industrial Gigabit Media Converter is not functioning properly, make sure the Industrial Gigabit Media Converter is set up according to instructions in this manual. The per port LED is not lit Solution: Check the cable connection of the Industrial Gigabit Media Converter.
62.5 1000BASE- SX MM 62.5 1000BASE- LX 5000* The single-mode port (1000BASE-LX port) of IGT-805AT / IGT-1205AT complies with LX 5 kilometers and provides an additional margin allowing for a 10/20/30/40/50/60/ 70/120 kilometer Gigabit Ethernet link on single mode Note...
Appendix A: Approved Planet SFP Transceivers PLANET Industrial Gigabit Media Converter supports 100/1000 dual mode with both single mode and multi-mode SFP transceivers. The following list of approved PLANET SFP transceivers is correct at the time of publication: Gigabit SFP Transceiver Modules...
B.2 RJ45 Cable Pin Assignments The standard RJ45 receptacle/connector There are 8 wires on a standard UTP/STP cable and each wire is color- coded. The following shows the pin allocation and color of straight cable and crossover cable connection: Straight Cable SIDE 1 SIDE 2 SIDE 1...
: Industrial 10/100/1000BASE-T to 2 100/1000BASE-X SFP Media Converter (-40~75 degrees C) *Model Number : IGT-1205AT * Produced by: : Planet Technology Corp. Manufacturer Name Manufacturer Address : 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.)
Page 36
Industrial 10/100/1000BASE-T to 100/1000BASE-X SFP Media Converter (-40~75 degrees C) *Model Number: IGT-805AT * Produced by: Planet Technology Corp. Manufacturer‘s Name : Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan (R.O.C.) is herewith confirmed to comply with the requirements set out in the Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility Directive on (2004/108/EC).