1. Package Contents Thank you for purchasing PLANET Industrial 802.3bt PoE++ Splitter, IPOE- 17xS Series. “PoE Splitter” mentioned in this manual refers to the IPOE- 17xS Series. The description of this series is shown below: IPOE-173S Industrial Single-Port 10/100/1000Mbps 802.3bt PoE++ Splitter IPOE-176S Industrial Single-Port 10Gbps 802.3bt PoE++ Splitter...
2. Product Specifications Product IPOE-173S IPOE-176S HW Version Hardware Specifications PoE Input 1 10/100/1000BASE-T 1 10M/100M/1G/2.5G/5G/10G Port RJ45 BASE-T RJ45 Data Output 1 10/100/1000BASE-T 1 10M/100M/1G/2.5G/5G/10G Port RJ45 BASE-T RJ45 Interface DC Out Plug 1 removable 4-pin terminal block Connector DIP Switch 12V/19V/24V DC output PoE Input: 30W (Green) 60W (Green)
Page 5
System on with PoE 5.3 watts 5.5 watts input Power Full loading Consump- with tion maximum 75.83 watts 75.45 watts 12V DC, 6.8A output 802.3 bt 12V DC, 6.8A (max.) Power type 4 19V DC, 4.3A (max.) Output PoE++ input 24V DC, 3.3A (max.) 802.3 bt Twisted-pair cable up to 100...
3. Hardware Introduction 3.1 Front Panel and LED Indicators IPOE-173S IPOE-176S PoE input indicators Color Function 30W 60W 90W 30W 60W 90W PoE Input PoE Input Lights to indicate the PoE Splitter is Green PoE In PoE In working in 802.3at PoE mode. Lights to indicate the PoE Splitter Green is working in 802.3bt type 3 PoE...
3.2 4-pin Power Output Terminal Block If there is no power socket in your network environment, PLANET IPOE-17xS Series provides DC power for this Ethernet device conveniently. The IPOE-17xS Series splits the transmission of the power and data. From top to down, there are Negative (V-), Negative (V-), Positive (V+) and Positive (V+), and two sets of DC power output contact.
3.3 DC Voltage DIP Switch It provides three kinds of DC power output through its DIP switch and its voltage and current are shown below: 10/100/1000/ 2.5G/5G/10G Power Output DC Voltage 12V 19V 24V Figure 3-3: DIP Switch of IPOE-17xS Series 1.
3.4 Grounding the Device Users MUST complete grounding wired with the device; otherwise, a sudden lightning could cause fatal damage to the device. Earth Ground EMD (Lightning) DAMAGE IS NOT COVERED UNDER WARRANTY.
4. Installation Wiring the Power Outputs Please follow the steps below to insert the power wires. Step 1: Please find one terminal block connector within two DC power outputs shown below: 1 V- 2 V- 3 V+ 4 V+ The wire gauge for the terminal block should be in the range of 12 ~ 24 AWG.
Page 12
Step 4: Install the terminal block on PLANET IPOE-17xS Series Splitter. Step 5: Connect the network copper cable (RJ45) from an 802.3bt PoE++ PSE to the IPOE-17xS Series Splitter where the power and data are separately transmitted to a PD as shown in the figure below (The following figure is based on the IPOE-173S. The display of the other...
5. Three-View Diagram IPOE-173S Top View Mounting Kit Side View Front View Side View Rear View 30W 60W 90W PoE Input PoE In DIN-Rail Kit 10/100/1000T Data Out 10/100/1000T Power Output DC Voltage 12V 19V 24V Bottom View Mounting Kit Unit: mm Figure 5-1: IPOE-173S Three-View Diagram...
Page 14
IPOE-176S Top View Mounting Kit Side View Front View Side View Rear View 30W 60W 90W PoE Input PoE In DIN-Rail Kit 10/100/1000/ 2.5G/5G/10G Data Out 10/100/1000/ 2.5G/5G/10G Power Output DC Voltage 12V 19V 24V Bottom View Mounting Kit Unit: mm Figure 5-2: IPOE-176S Three-View Diagram...
Customer Support Thank you for purchasing PLANET products. You can browse our online FAQ resource on PLANET web site first to check if it could solve your issue. If you need more support information, please contact PLANET support team. PLANET online FAQs: http://www.planet.com.tw/en/support/faq...
Page 16
FCC Warning This device has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.