Features; Before Using; Equipment Mains Working Setting; Inappropriate Places For Installation - Marantz CC4003 User Manual

ENGLISH

FEATURES

SUPPORTS MP3 AND WMA FILE
PLAYBACK
MP3 and WMA fi les that have been recorded onto
CD-R or CD-RW discs can be played back on this CD
player. (See page 14)
WHILE PLAYING A DISC, FOUR OTHER
DISCS CAN BE CHANGED
DIRECT DISC ACCESS BUTTON
Direct Disc Access button is equipped both on the
front panel of the unit and on the remote controller
for one-touch disc change to any of the 5 discs in
the unit.
VARIOUS PLAY MODES SUCH AS
RANDOM, PROGRAM AND REPEAT
HEADPHONE JACK WITH VOLUME
RS-232C CONTROL PORT AND IR FLASHER
INPUT
RS-232C port which supports both unit control
and operating status transmission is equipped to
enable central control with custom installation. Also,
Flasher input is equipped to realize wired control
when you cannot use remote control due to the
installation on the rack, etc.
5 SETS OF BUILT-IN REMOTE CONTROL
CODES
Because there are 5 sets of built-in remote control
code signals for between the unit and remote
controller, up to 5 units installed in the same place
can be remotely controlled independently.
ALUMINUM FRONT PANEL
Hairline finish aluminum front panel is used for
quality look.
2

BEFORE USING

EQUIPMENT MAINS
WORKING SETTING
Your Marantz product complies with the household
power and safety requirements in your area.
This product can be powered by 120 V AC only.
INAPPROPRIATE PLACES
FOR INSTALLATION
To keep your unit in perfect working order for the
longest possible time, avoid installing the unit in the
following locations.
• Wherever it will be exposed to direct sunlight
• Wherever it will be close to a heater or other heat-
radiating appliance
• Wherever the humidity is high or ventilation is
poor
• Wherever it is very dusty
• Wherever it will be subject to vibration
• On top of a rickety stand or in an unstable location
which is tilted at an angle
• Near windows where there is a chance of
exposure to rain, etc.
• On top of an amplifi er or other component which
dissipates a great deal of heat
To ensure proper heat dissipation, install the unit
while leaving clearances between the unit and
wall or other components, as shown in the fi gure
below.
Above 0.1 m
Left 0.1 m (4 in) Right 0.1 m
(4 in) or more
or more (4 in) or more
Rear 0.1 m (4 in) or more
DO NOT PLACE OBJECTS ON TOP
Refrain from placing any objects on top of the unit.

PRECAUTIONS

• In winter, droplets of water form on the insides
of the windows of a heated room: this is called
condensation. This unit uses an optical lens,
so the condensation may form in the following
cases.
- In a room immediately after the heating has
been turned on
- In a room where the humidity level is high
- When the unit has been suddenly brought from
a cold location into a warm room
Since, in cases like this, the track numbers
may not be read and the unit is prevented from
operating properly, wait about 30 minutes, and
then operate the unit.
• If this unit is placed on an object that generates
substantial heat, such as an amplifi er, the laser
inside this unit may be deteriorated.
• This unit may cause interference on a tuner or TV
set. If this is the case, place it further away from
the tuner or TV set.
• Compact discs have much less noise than analog
records and hardly any noise is heard before play
starts.
Bear in mind, therefore, that if the volume control
on the amplifier is set too high, you will risk
damaging other audio components.
• This unit cannot play CD-ROMs used with
personal computers, game CDs, video CDs,
DVDs (video/audio) or DTS-CDs.
• We do not recommend the use of lens cleaners.
• If this unit is placed in a rack with glass doors,
do not attempt to open the disc tray with the 0
OPEN/CLOSE button on the remote controller
with the glass doors shut. Impeded disc-tray
movement may result in a failure.
NOTES FOR REMOVING
SHIPPING SCREWS
At the bottom of the player there are two red
shipping screws for use when the player is
transported. Before using the player, turn these
screws counterclockwise and remove them.
If the shipping screws are still in place and the
power is turned on, unplug the power cord from the
power outlet and remove the shipping screws.
Retain these screws as they will be needed when
the player is transported.
Before transporting the player, take out the discs,
close the disc tray, set to standby mode and unplug
the power cord from the power outlet. Then install
the shipping screws by turning them clockwise. Be
sure to fasten them securely.
shipping screws