Troubleshooting Guide - Sherwood RD-606i Operating Instructions Manual

RD-606i(G)_ENG_110511_RD-606i(G)_ENG 2011-05-13 오전 9:57 페이지 52

Troubleshooting Guide

If a fault occurs, run through the table below before taking your receiver for repair.
If the fault persists, attempt to solve it by switching the receiver off and on again. If this fails to resolve the situation, consult
your dealer. Under no circumstances should you attempt to repair the receiver yourself. This could void the warranty.
PROBLEM
No power
No sound
No sound from the surround
speakers
No sound from the center
speaker
No picture
No picture with an HDMI
connection
Noise or distorted picture
Stations cannot be received
Preset stations cannot be
received
Poor FM reception
Continuous or intermittent hissing
noise during AM reception,
especially at night.
Cannot connect to network.
Internet radio broadcast cannot
be played.
Remote control unit does not
operate.
POSSIBLE CAUSE
• The AC input cord is disconnected.
• Poor connection at AC wall outlet or the outlet is
dead or off.
• The speaker wires are disconnected.
• The master volume is adjusted too low.
• The MUTE button is pressed to ON.
• Incorrect selection of input source.
• Incorrect connections between the components.
• The HDMI AUDIO OUT is set to THROUGH.
• The settings related to audio are set incorrectly.
• Surround mode is switched off(stereo mode).
• Master volume and surround level are too low.
• Monaural source is used.
• Surround speaker setting is "NO".
• Stereo mode, etc is selected.
• Center speaker setting is "NO".
• Master volume and center level are too low.
• Video connections between this unit and the
monitor TV are not made correctly.
• Incorrect selection of input source on the monitor
TV.
• HDMI connection between this unit and the
monitor TV are not made correctly.
• The monitor TV or other equipments do not
support HDCP.
• Video format of your monitor TV, DVD player, etc.
is different from PAL.
• No antenna is connected.
• The desired station frequency is not tuned in.
• Antenna is in wrong position.
• An incorrect station frequency has been memorized.
• The memorized stations are cleared.
• No antenna is connected.
• The antenna is not positioned for the best reception.
• Weak signals.
• Noise is caused by motors, fluorescent lamps or
lightning, etc.
• Network down.
• The computer's or router's firewall is activated.
• Ethernet cable is not properly conneted or
network is disconnected.
• Program is broadcasting in non-compatible
format.
• Internet radio station is not currently
broadcasting.
• Batteries are not loaded or exhausted.
• The remote sensor is obstructed.
52
REMEDY
• Connect cord securely.
• Check the outlet using a lamp or another
appliance.
• Check the speaker connections.
• Adjust the master volume.
• Press the MUTE button to cancel the muting effect.
• Select the desired input source correctly.
• Make connections correctly.
• Set it to AMP. (For details, refer to "When
selecting the HDMI AUDIO OUT" on page 50.)
• Set the settings correctly. (For details, refer to
"SETTING THE INPUT SETUP" on page 41.)
• Select a surround mode.
• Adjust master volume and surround level.
• Select a stereo or surround source.
• Select the desired surround speaker setting.
• Select the desired surround mode.
• Select the desired center speaker setting.
• Adjust master volume and center level.
• Make proper video connections.
• Select the input source correctly.
• Make proper HDMI connection.
• This unit will not output video signal unless the
connected equipments supports HDCP.
• Change the video format to PAL.
• Connect an antenna.
• Tune in the desired station frequency.
• Move antenna and retry tuning.
• Memorize the correct station frequency.
• Memorize the stations again.
• Connect an antenna.
• Change the position of the antenna.
• Install an outdoor FM antenna.
• Keep the receiver away from noise sources.
• Install an outdoor AM antenna.
• Check that network is working.
• Check the computer's or router's firewall settings.
• Check the connection status.
• Only internet radio programs in MP3 and WMA
formats can be played in this unit.
• Tune in a radio station that is currently
broadcasting.
• Replace the batteries.
• Remove the obstacle.